
The AirTAC SE63 Standard Cylinder SE63X70 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 70mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X70 is a double-acting single-rod ISO 15552 profile cylinder delivering 1559 N of push force and 1402 N of pull force at 0.5 MPa. Designed with a 63 mm bore and 70 mm stroke, it operates efficiently at speeds between 30 and 800 mm/s using a PT3/8 port.
Its square extruded aluminum barrel eliminates external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly in tight spaces. The field-adjustable air cushioning at both ends allows you to tune end-of-stroke deceleration precisely, protecting payloads from hard impacts. This specific SKU lacks a built-in magnet, so position sensing is not available without a model change.
| Model | Airtac SE63 Standard Cylinder SE63X70 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 70 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Routes continuous product flows on packaging lines using the 70 mm stroke and 1559 N push force to pivot guide arms without stalling.
Opens and closes heavy machine tool safety doors rapidly, relying on the adjustable pneumatic cushion to soften the 70 mm end-of-stroke impact.
Folds corrugated cardboard flaps during automated case sealing, utilizing the 1402 N retract force to pull mechanical folding arms cleanly.
With a 1559 N push at 0.5 MPa, this 63 mm bore fits neatly between the 50 mm (982 N push) and 80 mm (2513 N push) sizes, letting you scale force up or down as your payload demands. Because it is a standard double-acting cylinder, it cannot hold a load if air pressure drops—if your application requires static holding, consider the BSE rod-lock variant. For ISO 15552 direct retrofits, match the 63 mm bore, 70 mm stroke, PT3/8 port, and your required mounting accessory.
Quick checklist
At 0.5 MPa, the SE63X70 provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N. The maximum push force is 318 kgf when operating at the 1.0 MPa pressure limit.
No, the adjustable air cushion at both ends only decelerates the piston near the stroke limits; it does not act as a brake. If air is lost or the valve is centered, the piston will drift. For true load holding, you need a BSE series rod lock cylinder or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.