verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X700SN

The AirTAC SE63 Standard Cylinder SE63X700SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 700mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke700 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$176.77 $184.27Save 4% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X700SN

The AirTAC SE63X700 is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It generates 1559 N of push force and 1402 N of pull force at 0.5 MPa, scaling to a maximum output of 318 kgf at 1.0 MPa. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.

This 700 mm stroke variant integrates an NBR seal for standard pneumatic environments and includes a built-in magnet for non-contact position sensing. The field-adjustable air cushioning at both ends allows technicians to dial in end-of-stroke deceleration via a setscrew, softening hard impacts when cycling at speeds up to 800 mm/s.

Airtac SE63 Standard Cylinder SE63X700SN Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X700SN
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke700 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X700SN

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×700Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X700SN Is Used

conveyor_belt

Pallet Transfer Line Diverter

Leverages the 700 mm stroke to push heavy pallets onto a secondary conveyor lane, utilizing the 1559 N push force to overcome friction without stalling.

packaging

Corrugated Box Flap Folder

Deploys the long stroke to extend folding arms over wide packaging formats, relying on the adjustable end cushions to prevent tearing the cardboard at high speeds.

straighten

Automotive Press Unloader

Extracts stamped body panels from deep press dies, where the NBR seal withstands shop-air moisture and the magnet confirms full extraction.

Is the Airtac SE63 Standard Cylinder SE63X700SN the Right Cylinder?

When sizing this 63 mm bore actuator, evaluate your pressure constraints against neighboring bores. Stepping down to a 50 mm bore reduces the 0.5 MPa push to 982 N, while stepping up to an 80 mm bore increases it to 2513 N. Because this is a 700 mm stroke unit, the unsupported piston rod is highly susceptible to bending under lateral loads; always pair it with an external linear guide to prevent rod-bearing damage.

As a dimensionally interchangeable ISO 15552 cylinder, the SE63X700 serves as a direct replacement for other standard profile cylinders. It uses a PT3/8 port, features a Ø20 mm rod with an M16x1.5 thread, and its -S magnet pairs directly with AirTAC CMSE and DMSE sensors. Note that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load if air pressure is lost—use a BSE rod lock for position holding.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X700SN FAQ

At 0.5 MPa, the SE63X700 provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.

Yes, the SE63X700 is a true ISO 15552 profile cylinder with standardized mounting dimensions, making it dimensionally interchangeable with other ISO 15552 cylinders. It uses a PT3/8 port and its built-in magnet is specifically designed to interface with AirTAC CMSE and DMSE sensors.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X700SN

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X700SN and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.