
The AirTAC SE63 Standard Cylinder SE63X70FTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 70mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X70FTC is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 1559 N push force at 0.5 MPa. It features a 63 mm bore, a 70 mm stroke, and an integrated FTC mounting bracket for direct front-face attachment. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This unit relies on a field-adjustable pneumatic cushion at both ends to decelerate the piston near the stroke limits, protecting internal components from hard end-stop impacts. Note that this specific SKU is configured without a sensor magnet, meaning it cannot host CMSE or DMSE position switches without modification. The cushioning is a deceleration feature only and does not lock or hold the load if air pressure is lost.
| Model | Airtac SE63 Standard Cylinder SE63X70FTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 70 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N extend force to eject stamped metal sheets from a die, leveraging the short 70 mm stroke for rapid, high-frequency cycling.
Drives a mechanical arm to fold corrugated cardboard flaps on a packaging line, where the FTC mount provides rigid face-mounting against the machine frame.
Pushes bearings or bushings into housings on an assembly fixture, relying on the adjustable end cushions to prevent damage upon seating.
Selecting the SE63X70FTC makes sense when your application requires approximately 1559 N of push at 0.5 MPa. If you need less force, stepping down to the 50 mm bore yields 982 N of push, while stepping up to the 80 mm bore provides 2513 N. Because this model uses the standardized ISO 15552 mounting interface, it serves as a direct dimensional replacement for other ISO 15552 cylinders, utilizing the same FTC front flange hardware and PT3/8 port connections.
Keep in mind that a standard double-acting cylinder drifts when air is exhausted or the valve is centered; it cannot hold a vertical load safely without live pressure. If your fixture demands mechanical holding, you should pivot to the BSE rod-lock variant or employ an external pilot-operated check valve.
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No, this specific SKU is built without a built-in magnet. To use AirTAC CMSE reed or DMSE electronic sensors, the cylinder must be ordered with the 'S' option code. Additionally, its ISO 15552 profile ensures dimensional interchangeability with other standard profile cylinders.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.