
The AirTAC SE63 Standard Cylinder SE63X720S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 720mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X720S is a double-acting, single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 1559 N push force at 0.5 MPa. Its extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies sensor placement along any of its three integrated grooves. Equipped with a -S magnet, this unit directly supports AirTAC CMSE reed and DMSE electronic position switches for precise end-of-stroke verification.
Because this model carries a 720 mm stroke, it leverages a Ø20 mm piston rod and M16x1.5 thread to handle greater mechanical stress over that distance. Field-adjustable pneumatic cushioning at both ends allows technicians to tune the end-of-stroke deceleration via a set screw, softening hard impacts when moving heavy loads at high velocities.
| Model | Airtac SE63 Standard Cylinder SE63X720S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 720 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×720 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Pushes heavy timber or steel pallets onto secondary conveyor lines, utilizing the 1559 N push force to overcome friction across a 720 mm diversion stroke.
Drives mechanical arms to fold oversized corrugated carton flaps, relying on the -S magnet and DMSE sensors to confirm full extension before glue application.
Actuates sliding tray mechanisms in dense storage racks, where the tie-rod-free extruded profile maximizes vertical space efficiency and resists warehouse humidity.
Selecting the SE63X720S makes sense when your application requires a 720 mm reach with mid-range force. If you need less thrust, stepping down to the 50 mm bore drops the 0.5 MPa push to 982 N, while stepping up to the 80 mm bore raises it to 2513 N. As a dimensionally interchangeable ISO 15552 cylinder, this model serves as a direct replacement for other ISO 15552 profile cylinders, matching the 63 mm footprint, PT3/8 port, and standard mounting accessories without machining changes.
At 720 mm of stroke, the unsupported rod mass introduces a risk of rod-bearing bending under side loads; always pair this cylinder with an external guide rail to prevent premature seal wear. Note that the adjustable air cushion only decelerates the piston near the stroke ends—it does not lock or hold the load. If air pressure drops or the valve centers, the piston will drift, so deploy a BSE rod lock or external pilot-operated check valve for true position holding.
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE63X720S is dimensionally interchangeable per ISO 15552, meaning it shares the exact mounting interface, PT3/8 port size, and 63 mm bore footprint of other standard profile cylinders, allowing for seamless retrofits without altering your machinery.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.