verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X73S

The AirTAC SE63 Standard Cylinder SE63X73S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 73mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke73 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$85.83 $93.33Save 8% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X73S

The AirTAC SE63X73S is a double-acting, single-rod ISO 15552 profile cylinder engineered for rigorous pneumatic tasks. Delivering 1559 N of push force at 0.5 MPa, it features a 63 mm bore and a 73 mm stroke. Its square extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.

Equipped with a built-in magnet (S option), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushioning at both ends allows technicians to dial in end-stop deceleration via a setscrew, softening impacts during high-speed 30-800 mm/s cycles.

Airtac SE63 Standard Cylinder SE63X73S Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X73S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke73 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X73S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×73Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X73S Is Used

packaging

Carton Erector Jaws

Provides the 1559 N push at 0.5 MPa needed to fold and seal corrugated carton flaps rapidly on high-speed packaging lines.

factory

Injection Mould Ejector

Uses the 73 mm stroke and integrated DMSE sensor feedback to eject plastic parts from moulding presses with precise timing.

straighten

Metal Stamping Stripper

Applies consistent hold-down force to strip sheet metal blanks from progressive stamping dies during retraction.

Is the Airtac SE63 Standard Cylinder SE63X73S the Right Cylinder?

If your application requires slightly less thrust, the adjacent SE50 bore provides 982 N of push at 0.5 MPa, whereas stepping up to the SE80 bore yields 2513 N for heavier payloads. Because this is a standard double-acting cylinder, it cannot hold a load statically if air pressure drops or the valve centers; for fail-safe position holding, consider the BSE rod-lock variant. At 73 mm, side-load stress on the M16x1.5 rod bearing is minimal, but always verify guide alignment.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X73S FAQ

At 0.5 MPa, the SE63X73S provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, push increases to 2182 N. The absolute maximum thrust is 318 kgf at 1.0 MPa operating pressure.

Yes, the SE63X73S is dimensionally interchangeable per ISO 15552 standards. It shares the exact mounting interface and PT3/8 port locations of other ISO 15552 profile cylinders, allowing a direct retrofit without modifying your machine base.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X73S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X73S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.