
The AirTAC SE63 Standard Cylinder SE63X75FTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 75mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X75FTC is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force at 0.5 MPa. The extruded aluminum square barrel omits external tie rods entirely, yielding a compact, corrosion-resistant envelope that mounts flush against machine frames. This FTC center-trunnion configuration provides a pivoting anchor point that handles angular rod deflection during dynamic motion cycles.
Field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-of-stroke deceleration via a set screw, preventing hard mechanical impacts when cycling at speeds up to 800 mm/s. This specific SKU is manufactured without a built-in piston magnet, meaning it does not support direct CMSE or DMSE electronic position sensing without modification.
| Model | Airtac SE63 Standard Cylinder SE63X75FTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 1559 N push force required to mechanically fold heavy cardboard flaps during high-speed case erector operations without stalling.
Uses the FTC trunnion mount to pivot a diverter arm smoothly across a conveyor belt, routing standard wooden pallets between processing lanes.
Drives the safety interlock door on an injection molding cell, utilizing the 75 mm stroke to clear the mold area for robotic extraction arms.
Delivering 1559 N push at 0.5 MPa, this 63 mm bore is properly sized for medium-duty positioning. If your payload requires less force, stepping down to the 50 mm bore yields 982 N push, while moving up to the 80 mm bore provides 2513 N push for heavier lifting. Because this is a double-acting cylinder, it cannot hold a position or resist drift if air pressure drops; use a BSE rod lock for fail-safe holding. The 75 mm stroke avoids the side-load bearing stress seen in longer strokes, but an external guide is still recommended for heavy lateral loads.
As a true ISO 15552 cylinder, the SE63X75FTC is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing you to drop it into existing FTC trunnion footprints without machining new mounting plates. It uses a PT3/8 port and a Ø20 mm hard-chrome rod.
Quick checklist
At 0.5 MPa, the SE63X75FTC generates 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N. The absolute maximum push force is 318 kgf at 1.0 MPa operating pressure.
Yes. The SE63X75FTC is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting interface, bore spacing, and FTC trunnion dimensions as other ISO 15552 profile cylinders, allowing for direct retrofitting.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.