
The AirTAC SE63 Standard Cylinder SE63X800 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 800mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X800 is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding linear motion tasks. Operating at 0.5 MPa, it generates 1559 N of push force and 1402 N of pull force, scaling to a maximum of 318 kgf at 1.0 MPa. Its square extruded aluminum barrel completely eliminates external tie rods, yielding a highly compact, corrosion-resistant body that mounts flush against machine frames without protruding hardware.
This 63mm bore unit features a PT3/8 port and a 20mm piston rod with an M16x1.5 thread. Because this specific SKU lacks the -S magnet suffix, it does not support AirTAC CMSE or DMSE position sensing out of the box. The cylinder relies on field-adjustable air cushions at both ends, allowing technicians to dial in the end-of-stroke deceleration via a set screw to prevent hard mechanical impacts during its 800mm travel.
| Model | Airtac SE63 Standard Cylinder SE63X800 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Pushes 3-meter raw bar stock through the spindle with 1559 N of force, utilizing the 800mm stroke to minimize reload cycles.
Indexes heavy loaded pallets along a roller conveyor, relying on the field-adjustable air cushion to soften the hard end stops at high travel speeds.
Extracts large molded plastic parts from deep cavities, where the 20mm rod and M16x1.5 thread provide robust resistance against off-center stripping loads.
If your application requires less force, stepping down to the 50mm bore yields 982 N of push at 0.5 MPa, while moving up to the 80mm bore provides 2513 N. As a standard ISO 15552 profile cylinder, it is dimensionally interchangeable with other ISO 15552 cylinders, making it a direct replacement for retrofits. To match this exact configuration, you need a 63mm bore, 800mm stroke, PT3/8 port, and basic mounting. Note that an 800mm stroke creates significant leverage on the rod bearing; an external guide is strongly recommended to prevent bending under side loads. Furthermore, the adjustable air cushion only decelerates the piston near stroke end—it will not hold a load if air pressure is lost. For position holding, consider the BSE rod lock variant.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
The SE63X800 delivers 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum of 318 kgf at 1.0 MPa. It operates at speeds of 30-800 mm/s.
Yes, the SE63X800 is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint and body dimensions as other ISO 15552 profile cylinders for direct replacement.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.