Airtac SE32 Standard Cylinder SE32BX300SN
The AirTAC SE32 Standard Cylinder SE32BX300SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 300mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke300 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE32 Standard Cylinder SE32BX300SN
The AirTAC SE32BX300SN is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering 402 N of push force at 0.5 MPa. Its square extruded aluminum barrel removes external tie rods entirely, yielding a compact body that mounts flush against frames and shrinks the overall footprint. This clean profile naturally resists debris buildup and corrosion.
Equipped with a SUS304 stainless steel rod and NBR seals, this unit is tailored for corrosive environments or washdown duty. The integrated magnet (-S) supports CMSE reed and DMSE electronic position sensors, which seat directly into the multiple sensor grooves machined into the barrel. Field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration via a set screw, preventing hard impacts during high-speed 30-800 mm/s cycling.
Airtac SE32 Standard Cylinder SE32BX300SN Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32BX300SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 300 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32BX300SN
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32BX300SN Is Used
Lab Diagnostic Ejector
Uses the SUS304 rod and NBR seal to safely push chemical reagent trays out of a washdown station, relying on 402 N of thrust to overcome cartridge friction.
Pouch Sealing Blade
Cycles at 30-800 mm/s to drive a heated sealing jaw on a vertical form-fill machine, using the adjustable cushion to soften the 300 mm stroke impact.
PCB Panel Diverter
Deploys a deflecting gate on an SMT line, where the compact tie-rod-free profile allows tight mounting between conveyor belts without snagging wiring.
Is the Airtac SE32 Standard Cylinder SE32BX300SN the Right Cylinder?
Choosing this 32 mm bore makes sense when your application requires 402 N push at 0.5 MPa but would be over-served by larger, slower cylinders. If you need less force, there is no smaller standard ISO 15552 bore in the SE range, so you would step down to a compact SMC or Festo profile cylinder. If your load demands more thrust, stepping up to the 40 mm bore increases your push force to 628 N at 0.5 MPa. Because this is a 300 mm stroke, the 12 mm rod and rod bearing face increased bending moments under side loads; always support the load with an external guide to prevent premature seal wear. As a standard double-acting cylinder, it will drift if air pressure is lost, so specify a BSE rod lock variant if you need strict position holding. It serves as a direct replacement for any ISO 15552 cylinder sharing the 32 mm bore, 300 mm stroke, PT1/8 port, and basic mounting interface.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32BX300SN FAQ
At 0.5 MPa it provides 402 N push and 345 N pull. At 0.7 MPa the push increases to 563 N, and the maximum push is 82 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE32BX300SN is dimensionally interchangeable per ISO 15552. You can drop it in as a replacement for other 32 mm bore profile cylinders as long as you match the 300 mm stroke, PT1/8 port, and mounting accessories.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32BX300SN
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.