Airtac SE32 Standard Cylinder SE32BX30S
The AirTAC SE32 Standard Cylinder SE32BX30S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 30mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke30 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE32 Standard Cylinder SE32BX30S
The AirTAC SE32BX30S is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a 402 N push at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact body that mounts flush against machine frames while resisting corrosion. The SUS304 stainless steel rod makes it highly suited for washdown or chemically hostile environments.
Equipped with a built-in magnet, this unit interfaces directly with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends allows you to tune the 27 mm cushion length via a set screw, softening hard end stops during rapid 30-800 mm/s cycles.
Airtac SE32 Standard Cylinder SE32BX30S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32BX30S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32BX30S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32BX30S Is Used
Lab Dispenser Clamping
Secures small vial capping heads in analytical equipment, utilizing the 402 N push force and SUS304 rod to resist aggressive chemical cleaning agents.
Pouch Sealing Jaws
Actuates the lower sealing jaw on compact vertical form-fill-seal machines, where the 30 mm short stroke provides rapid open-close cycles.
PCB Router Gating
Controls the entry gate on a printed circuit board routing conveyor, using the integrated magnet and DMSE sensor to confirm paddle position.
Is the Airtac SE32 Standard Cylinder SE32BX30S the Right Cylinder?
If your application requires less force, the SE32 is the smallest standard bore in this series, meaning you would look outside the ISO 15552 family for a smaller footprint. If you need to step up, the 40 mm bore provides a 628 N push at 0.5 MPa. Because this is a 30 mm stroke, side-loading on the 12 mm rod is minimal, but always ensure the load is axially aligned to prevent rod-bearing wear.
As a double-acting cylinder, the SE32BX30S relies on continuous air pressure to hold a load; it will drift if air is lost or the valve is centered. For position-holding safety, consider a BSE rod-lock variant. To replace an existing unit, match the 32 mm bore, 30 mm stroke, PT1/8 port, and your required mounting accessory.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32BX30S FAQ
At 0.5 MPa, this 32 mm bore cylinder provides 402 N of push force and 345 N of pull force. At 0.7 MPa, the push increases to 563 N, with a maximum push capacity of 82 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE32BX30S is dimensionally interchangeable per ISO 15552 standards. You can drop it in as a replacement for other ISO 15552 profile cylinders by matching the 32 mm bore, 30 mm stroke, PT1/8 port, and mounting interface.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32BX30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.