Airtac SE32 Standard Cylinder SE32X1000
The AirTAC Airtac SE32 Standard Cylinder SE32X1000 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 1000mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke1000 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X1000
The AirTAC SE32X1000 is a double-acting single-rod ISO 15552 profile cylinder engineered for a 32 mm bore and a 1000 mm stroke. Because this stroke exceeds the standard 1000 mm limit for this bore, it is provided as a made-to-order unit. It generates 402 N of push force and 345 N of pull force at 0.5 MPa, utilizing a 12 mm hard-chrome plated rod with an M10x1.25 thread.
The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant profile that mounts flush while exposing sensor grooves on three sides. Note that this specific SKU lacks the built-in magnet (-S), meaning it is not equipped for CMSE or DMSE position sensing out of the box. Field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration via a screw rather than relying on a fixed rubber bumper.
Airtac SE32 Standard Cylinder SE32X1000 Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X1000 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 1000 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X1000
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X1000 Is Used
Printed Circuit Board Testing
Drives a 1000 mm probe carriage across multi-panel PCB arrays, using the 402 N push force to maintain consistent contact pressure without deflecting the 12 mm rod.
Packaging Transfer Arm
Shuttles lightweight cardboard cartons between parallel conveyor belts over a full meter of travel, relying on the adjustable end cushions to soften high-speed stops.
Laboratory Sample Dispenser
Moves fluid vials along a long axis within analytical equipment, leveraging the flush tie-rod-less barrel to minimize contamination traps and save space.
Is the Airtac SE32 Standard Cylinder SE32X1000 the Right Cylinder?
Stepping up to the 40 mm bore increases your 0.5 MPa push to 628 N, whereas dropping down is not an option as 32 mm is the smallest available SE size. Because this is a non-standard 1000 mm stroke, verify your lead time during the RFQ process. With a PT1/8 port and M10x1.25 rod thread, it shares the ISO 15552 mounting interface for direct hardware interchangeability. At 1000 mm of unsupported extension, the 12 mm rod is highly susceptible to bending under side loads; an external guide bearing is strongly recommended to prevent premature seal failure. Remember that a standard SE does not hold position unpowered—consider a BSE variant if mid-stroke locking is required.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X1000 FAQ
At 0.5 MPa it provides 402 N push and 345 N pull; at 0.7 MPa it provides 563 N push. The maximum push force is 82 kgf at the 1.0 MPa operating pressure limit.
Yes, it is dimensionally interchangeable per ISO 15552 standards, allowing you to drop it into existing mounting hardware. However, this SKU lacks the -S magnet, so it cannot host CMSE or DMSE sensors without modification.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X1000
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.