Airtac SE32 Standard Cylinder SE32X100S
The AirTAC Airtac SE32 Standard Cylinder SE32X100S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 100mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke100 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X100S
The AirTAC SE32X100S is a double-acting single-rod ISO 15552 profile cylinder engineered for compact automation, delivering a 402 N push at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machine frames while retaining the standardized ISO 15552 footprint.
Equipped with a built-in magnet (S option), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensors without extra hardware. The field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration via a set screw, protecting the 12 mm rod and tooling during high-speed 30-800 mm/s cycles.
Airtac SE32 Standard Cylinder SE32X100S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X100S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X100S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X100S Is Used
Lab Analyzer Sample Routing
Drives a 100 mm linear push to insert test cartridges into diagnostic chambers, where the 402 N force is sufficient to seat the cartridge without crushing delicate medical components.
PCB Panel Ejection Station
Utilizes the built-in magnet and DMSE electronic sensors to confirm full extension at 800 mm/s, gently pushing populated circuit boards out of a testing fixture.
Small Carton Flap Folding
Deploys the 345 N retract force to tuck corrugated side flaps on compact packaging lines, relying on the adjustable cushion to prevent harsh impacts at stroke end.
Is the Airtac SE32 Standard Cylinder SE32X100S the Right Cylinder?
Selecting the SE32X100S is ideal when your application requires precise 100 mm travel within a tight force budget, offering 402 N push and 345 N pull at 0.5 MPa. If you need to step up power, the next bore up is the 40 mm cylinder providing 628 N push; stepping down is not an option as 32 mm is the smallest standard ISO 15552 bore in this series.
Because this is a double-acting cylinder, it will drift if air pressure is lost or the valve is centered, so it cannot hold a load safely without live pressure. For position-holding safety, consider pairing it with an external pilot-operated check valve or exploring the BSE rod-lock variant. As a true ISO 15552 profile cylinder, it serves as a drop-in replacement for any standard 32 mm bore, 100 mm stroke unit with PT1/8 ports and standard mounting accessories.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X100S FAQ
The SE32X100S delivers a push force of 402 N and a pull force of 345 N at 0.5 MPa. At 0.7 MPa, the push force is 563 N, with a maximum push capacity of 82 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE32X100S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can use it as a drop-in replacement for other 32 mm bore profile cylinders with a 100 mm stroke, matching the PT1/8 port and standard mounting dimensions.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.