Airtac SE32 Standard Cylinder SE32X100SFTC
The AirTAC Airtac SE32 Standard Cylinder SE32X100SFTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 100mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke100 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X100SFTC
The AirTAC SE32X100SFTC is a double-acting single-rod ISO 15552 profile cylinder engineered for compact actuation. It delivers 402 N of push force at 0.5 MPa and features a 100 mm stroke, a 12 mm rod, and a PT1/8 port.
This variant includes a built-in magnet for CMSE and DMSE position sensing, paired with an FTC mounting accessory. The extruded aluminum barrel omits external tie rods for a flush, corrosion-resistant exterior, while the field-adjustable air cushioning at both ends lets you fine-tune end-of-stroke deceleration to soften hard impacts.
Airtac SE32 Standard Cylinder SE32X100SFTC Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X100SFTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X100SFTC
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X100SFTC Is Used
PCB Router Spindle Z-Axis
Lifts and lowers a light-duty spindle with 402 N of push force, using the built-in magnet and DMSE sensor to verify the upper tool-change position.
Small Pouch Flap Folder
Actuates a folding blade at 100 mm stroke, relying on the field-adjustable air cushion to soften the end stop and prevent tearing thin film.
Lab Dispenser Valve Tap
Opens and closes a pneumatic dispensing valve in a clean environment, where the tie-rod-free aluminum profile wipes down easily.
Is the Airtac SE32 Standard Cylinder SE32X100SFTC the Right Cylinder?
At 0.5 MPa, this 32 mm bore generates 402 N of push force. If you need less output, there is no smaller SE bore, but if your application demands more thrust, stepping up to the 40 mm bore yields 628 N of push at 0.5 MPa. Because this is a 100 mm stroke, side-load bending on the 12 mm rod bearing is minimal, though long unsupported strokes still require an external guide.
The SE32X100SFTC is dimensionally interchangeable per ISO 15552, serving as a drop-in replacement for other ISO 15552 cylinders. Remember that the adjustable air cushion only decelerates the piston near the stroke end; it does not hold a load. If air is lost, the piston drifts, so use a BSE rod lock for position holding. To match this exact unit, specify: 32 mm bore, 100 mm stroke, PT1/8 port, FTC mount, and the -S magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X100SFTC FAQ
At 0.5 MPa, this 32 mm bore cylinder provides 402 N of push force and 345 N of pull force. At 0.7 MPa, the push force is 563 N. The maximum push force is 82 kgf at 1.0 MPa.
Yes. The SE32X100SFTC is dimensionally interchangeable per ISO 15552 mounting interfaces, allowing it to drop in for other ISO 15552 profile cylinders. It uses a PT1/8 port and includes an FTC mount and a built-in magnet for CMSE or DMSE sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X100SFTC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.