Airtac SE32 Standard Cylinder SE32X145
The AirTAC Airtac SE32 Standard Cylinder SE32X145 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 145mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke145 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X145
The AirTAC SE32X145 is a double-acting, single-rod ISO 15552 profile cylinder engineered for compact pneumatics. It yields 402 N of push force at 0.5 MPa and operates seamlessly within a 30-800 mm/s speed range. The square extruded aluminum barrel omits external tie rods, delivering a flush-mounting corrosion-resistant body that integrates effortlessly into tight machine frames.
This unit features field-adjustable air cushioning at both ends, allowing technicians to tune end-of-stroke deceleration via a set screw rather than enduring harsh fixed bumper impacts. Because this specific SKU lacks the -S magnet, it is not wired for CMSE or DMSE position sensing out of the box. The 145 mm stroke utilizes a 12 mm hard-chrome rod with an M10x1.25 thread, supported by a 27 mm cushion length to smooth out high-cycle transitions.
Airtac SE32 Standard Cylinder SE32X145 Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X145 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 145 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X145
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×145 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X145 Is Used
PCB Handling
Provides 402 N of push to route bare printed circuit boards through pick-and-place machinery without marring delicate traces.
Carton Sealing
Cycles the 145 mm stroke to fold small corrugated carton flaps, using adjustable cushions to prevent tearing the cardboard.
Lab Dispensing
Actuates precision metering valves for reagent dosing, benefiting from the smooth 30-800 mm/s speed range and clean profile body.
Is the Airtac SE32 Standard Cylinder SE32X145 the Right Cylinder?
Delivering 402 N push at 0.5 MPa, this 32 mm bore fits light-duty tasks. If you need less force, there is no smaller standard SE bore, but stepping up to the 40 mm bore provides 628 N of push. For ISO 15552 dimensional drop-in replacements, match the 32 mm bore, 145 mm stroke, PT1/8 port, and your required mounting accessory. Note that a plain SE exhausts and drifts when air is lost; it cannot hold a load without live pressure, so consider a BSE rod lock for strict safety requirements. At 145 mm, side-load stress on the rod bearing is minimal, but external guides are recommended for heavy offset loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X145 FAQ
At 0.5 MPa, the SE32X145 delivers 402 N push and 345 N pull. At 0.7 MPa, push increases to 563 N, with a maximum push of 82 kgf at 1.0 MPa. It uses a PT1/8 port and an M10x1.25 rod-end thread.
Yes, the SE32X145 is dimensionally interchangeable with other ISO 15552 profile cylinders. You can swap it directly using the existing 32 mm bore mounting hardware and PT1/8 pneumatic connections without altering the machine frame.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X145
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.