Airtac SE32 Standard Cylinder SE32X150S
The AirTAC Airtac SE32 Standard Cylinder SE32X150S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 150mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke150 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X150S
The AirTAC SE32X150S is a double-acting single-rod profile cylinder built to ISO 15552 / VDMA 24562 standards. It delivers a 402 N push and 345 N pull at 0.5 MPa, making it well-suited for compact automation tasks requiring a 150 mm stroke. The integrated -S magnet enables direct position feedback using AirTAC CMSE reed or DMSE electronic sensors.
This unit utilizes a square extruded aluminum barrel without external tie rods, resulting in a flush, corrosion-resistant body that simplifies mounting in tight spaces. Field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration, protecting payloads from harsh impacts.
Airtac SE32 Standard Cylinder SE32X150S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X150S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X150S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X150S Is Used
PCB Depaneling Router
Provides the precise 402 N push at 0.5 MPa needed to plunge and route custom circuit board outlines without stressing the substrate.
Small Carton Flap Folder
Uses the 150 mm stroke to fold corrugated box flaps at high cycling speeds, relying on the adjustable cushion to prevent harsh mechanical stops.
Lab Sample Dispenser
Actuates a 12 mm rod to accurately drive a pipetting head, using the built-in S magnet with DMSE sensors to verify fluid draw limits.
Is the Airtac SE32 Standard Cylinder SE32X150S the Right Cylinder?
When sizing this 32 mm bore actuator, compare its 402 N push at 0.5 MPa against your actual load requirements. If your application demands less force, stepping down is not an option as 32 mm is the smallest available SE bore. Conversely, if you need more thrust, the next size up is the 40 mm bore, which provides a 628 N push at 0.5 MPa. Because this cylinder has a 150 mm stroke, it remains below the threshold where severe rod-bearing bending typically occurs, though external guides should still support any heavy lateral loads.
For retrofits, this model is dimensionally interchangeable per ISO 15552, meaning it drops directly into existing footprints using standard mounting hardware. It features a PT1/8 port and an M10x1.25 rod thread. Remember that a standard SE cylinder does not hold position or carry loads when air pressure is lost; if your process requires fail-safe load holding, consider the AirTAC BSE rod lock variant instead.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X150S FAQ
The SE32X150S generates a push force of 402 N and a pull force of 345 N at 0.5 MPa. At 0.7 MPa, the push force increases to 563 N, with a maximum push capacity of 82 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE32X150S is dimensionally interchangeable per ISO 15552. It shares the standardized mounting interface and hole patterns of other ISO 15552 profile cylinders, allowing it to serve as a direct drop-in replacement without modifying your machine plate.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X150S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.