Airtac SE32 Standard Cylinder SE32X150SFTC
The AirTAC Airtac SE32 Standard Cylinder SE32X150SFTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 150mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke150 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X150SFTC
The AirTAC SE32X150SFTC is a double-acting single-rod ISO 15552 profile cylinder engineered for compact automation. Operating at 0.5 MPa, it generates 402 N of push force and 345 N of pull force, scaling to a maximum of 82 kgf at 1.0 MPa. The extruded aluminum barrel omits external tie rods, yielding a smooth, corrosion-resistant body that mounts flush within tight machine envelopes.
Equipped with an FTC center trunnion mounting interface and a built-in magnet (-S), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors. The field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration, effectively absorbing impact energy without relying on fixed rubber bumpers.
Airtac SE32 Standard Cylinder SE32X150SFTC Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X150SFTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X150SFTC
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X150SFTC Is Used
PCB Depaneling Router
Actuates the cutting head on a depaneling machine, utilizing the 150mm stroke and 402 N push force to cleanly separate routed circuit boards.
Package Divert Arm
Mounts via the FTC trunnion to pivot a divert arm on a conveyor belt system, using the built-in magnet to trigger DMSE electronic sensors for position confirmation.
Lab Dispensing Valve
Precisely opens and closes a pneumatic dispensing valve for reagent application, relying on the adjustable cushion to prevent liquid splashing at the stroke ends.
Is the Airtac SE32 Standard Cylinder SE32X150SFTC the Right Cylinder?
Generating 402 N of push at 0.5 MPa, this 32mm bore is suited for light-load actuation. If your assembly requires less force, stepping down to the 25mm bore yields a smaller footprint, while stepping up to the 40mm bore provides 628 N of push for heavier resistance. For drop-in ISO 15552 retrofits, verify the 150mm stroke, PT1/8 port, FTC trunnion mount, and the -S magnet requirement.
Because the 150mm stroke is substantial for a 32mm bore, the 12mm rod and its bearing are subjected to higher bending moments under side loads. To prevent premature wear, an external guide rail should support the load. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load if air pressure is lost.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X150SFTC FAQ
The SE32X150SFTC provides a push force of 402 N and a pull force of 345 N at 0.5 MPa. At 0.7 MPa, the push force increases to 563 N, with a maximum push of 82 kgf at 1.0 MPa. The operational speed ranges from 30 to 800 mm/s.
Yes, the SE32X150SFTC is dimensionally interchangeable per ISO 15552 standards, serving as a drop-in replacement for other ISO 15552 profile cylinders. It shares the standardized mounting footprint and utilizes a PT1/8 port.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X150SFTC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.