Airtac SE32 Standard Cylinder SE32X210SLB
The AirTAC Airtac SE32 Standard Cylinder SE32X210SLB is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 210mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke210 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X210SLB
The AirTAC SE32X210SLB is a double-acting single-rod profile cylinder built to the ISO 15552 standard. It delivers a push force of 402 N and a pull force of 345 N at 0.5 MPa, making it well-suited for compact actuation tasks. This specific configuration includes an LB foot mounting bracket for secure horizontal bolting and a built-in magnetic piston for position sensing.
The extruded aluminum barrel design eliminates external tie rods, resulting in a smooth, corrosion-resistant profile that mounts flush against machine frames. Field-adjustable air cushioning at both ends allows you to tune the end-of-stroke deceleration via a set screw, preventing harsh impacts when cycling at speeds up to 800 mm/s. The integrated magnet supports AirTAC CMSE reed and DMSE electronic sensors along the multiple sensor grooves.
Airtac SE32 Standard Cylinder SE32X210SLB Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X210SLB |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 210 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X210SLB
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×210 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X210SLB Is Used
PCB Depaneling Saw
Provides the 402 N push force required to advance small printed circuit board panels through a routing saw at a controlled 210 mm stroke.
Carton Flap Folder
Uses the LB foot mount to secure the cylinder horizontally, timing the 210 mm stroke to fold minor carton flaps prior to tape sealing.
Lab Dispenser Positioning
Leverages the built-in magnet with DMSE electronic sensors to accurately confirm the 12 mm rod position for liquid dispensing heads.
Is the Airtac SE32 Standard Cylinder SE32X210SLB the Right Cylinder?
Selecting this 32 mm bore makes sense when your application requires roughly 402 N of push force at 0.5 MPa. If you need less force, there is no smaller standard ISO 15552 bore in this series, so you would look at non-ISO compact cylinders. If your load demands more power, stepping up to the 40 mm bore increases your push force to 628 N at 0.5 MPa. Because this unit features the -S magnet, you can directly mount CMSE or DMSE sensors without modifying the cylinder.
With a 210 mm stroke, the 12 mm piston rod is subjected to bending moments under lateral loads; for any stroke of 300 mm or longer, adding an external guide rail is critical to prevent rod-bearing wear. Note that a standard double-acting cylinder does not hold its position if air pressure is lost or the valve is centered, as the piston will drift. If your application requires true load holding without live air pressure, consider the BSE rod-lock variant. This model is dimensionally interchangeable with any ISO 15552 cylinder, simplifying retrofits.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X210SLB FAQ
At 0.5 MPa, this 32 mm bore cylinder provides 402 N of push force and 345 N of pull force. At 0.7 MPa, the push force increases to 563 N, with a maximum push capacity of 82 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE32X210SLB is dimensionally interchangeable per ISO 15552 standards. You can use it as a drop-in replacement for other ISO 15552 profile cylinders with a 32 mm bore and 210 mm stroke, utilizing the same mounting hardware and PT1/8 port threads.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X210SLB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.