Airtac SE32 Standard Cylinder SE32X215
The AirTAC Airtac SE32 Standard Cylinder SE32X215 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 215mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke215 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X215
The AirTAC SE32X215 is a double-acting, single-rod ISO 15552 profile cylinder engineered for compact pneumatics. It yields 402 N of push force at 0.5 MPa and operates via a PT1/8 port. Because this 215 mm stroke exceeds the standard 1000 mm maximum for a 32 mm bore, it is supplied as a non-standard, made-to-order unit.
The extruded aluminum barrel omits external tie rods, granting flush mounting access and corrosion resistance. Field-adjustable pneumatic cushioning at both ends lets you tune end-of-stroke deceleration to protect tooling. This SKU lacks a built-in magnet, so it does not support CMSE or DMSE position sensors without modification.
Airtac SE32 Standard Cylinder SE32X215 Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X215 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 215 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X215
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×215 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X215 Is Used
Lab Diagnostic Dispenser
Drives a 215 mm stroke to puncture reagent vials with 402 N push at 0.5 MPa, relying on the adjustable cushion to soften the impact.
PCB Edge Guide
Extends across a conveyor to align small electronics panels, using the compact 32 mm profile to fit tight machine frames.
Small Part Ejector
Pushes lightweight plastic moldings out of a die over 215 mm, benefiting from the 30-800 mm/s speed range for rapid cycling.
Is the Airtac SE32 Standard Cylinder SE32X215 the Right Cylinder?
This 32 mm bore generates 402 N push at 0.5 MPa. If your application needs less force, there is no smaller ISO 15552 bore, but stepping up to a 40 mm bore provides 628 N push. For load-holding safety, remember this standard cylinder drifts when air is lost; a BSE rod lock variant is required for fail-safe braking.
At 215 mm, the stroke is non-standard and made-to-order. The 12 mm rod and M10x1.25 thread handle moderate side loads, but for strokes over 300 mm, an external guide is strongly recommended to prevent rod-bearing bending.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X215 FAQ
At 0.5 MPa, the SE32X215 provides 402 N push and 345 N pull. At 0.7 MPa, push increases to 563 N. The maximum push force is 82 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable with other ISO 15552 cylinders, allowing you to reuse existing FA or LB mounting hardware. Note that this specific SKU lacks a sensor magnet, so it cannot host CMSE or DMSE switches without modification.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X215
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.