Airtac SE32 Standard Cylinder SE32X30S
The AirTAC Airtac SE32 Standard Cylinder SE32X30S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 30mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke30 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X30S
The AirTAC SE32X30S is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a 402 N push at 0.5 MPa. Its 30 mm stroke makes it highly effective for short-travel clamping and ejection tasks. The square extruded aluminum barrel hides the tie rods internally, yielding a smooth, corrosion-resistant exterior that mounts flush against machine frames.
Because this unit includes the -S magnet code, it is fully primed for CMSE reed or DMSE electronic position sensing. You can fine-tune the end-of-stroke deceleration using the adjustable air cushioning at both ends, ensuring quiet transitions even at rapid cycle rates.
Airtac SE32 Standard Cylinder SE32X30S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X30S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X30S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X30S Is Used
PCB Ejector Pins
Uses the precise 30 mm stroke and 402 N force to push bare circuit boards out of routing fixtures without damaging the substrate.
Carton Flap Folding
Deploys the built-in magnet and DMSE sensors to time rapid 30 mm strokes, folding small box flaps at high speeds on packaging lines.
Light-Duty Spot Clamps
Leverages the compact 32 mm profile body to secure thin sheet metal brackets during spot welding or riveting operations.
Is the Airtac SE32 Standard Cylinder SE32X30S the Right Cylinder?
Selecting the SE32X30S gives you 402 N of push force at 0.5 MPa. If your assembly requires less force, the smallest standard ISO 15552 bore in this range is 32 mm, so you cannot step down within this series. If you need more power, stepping up to the 40 mm bore yields 628 N of push at 0.5 MPa. This 30 mm stroke is very short, so side-load stress on the rod bearing is minimal, though external guides are always recommended for rigid loads.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a drop-in replacement for other 32 mm bore profile cylinders, matching the PT1/8 port and standard mounting accessories. Remember that the adjustable cushion only softens the end stops; it does not hold the load. If air pressure drops, the piston will drift, so add a BSE rod lock for fail-safe holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X30S FAQ
At 0.5 MPa, the push force is 402 N and the pull force is 345 N. At 0.7 MPa, the push force is 563 N. The maximum push force is 82 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE32X30S is dimensionally interchangeable per ISO 15552 standards. It shares the same 32 mm mounting footprint, PT1/8 port, and M10x1.25 rod thread, allowing it to serve as a direct drop-in replacement for other ISO 15552 profile cylinders.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.