Airtac SE32 Standard Cylinder SE32X30SH
The AirTAC Airtac SE32 Standard Cylinder SE32X30SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 30mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke30 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X30SH
The AirTAC SE32X30SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for high-temperature automation. Delivering 402 N of push force at 0.5 MPa, this 32 mm bore unit is built around an extruded aluminum barrel that eliminates external tie rods. This clean-profile design resists corrosion and allows accessories to mount flush against the body, saving valuable space in tight machine cells.
Because this configuration carries the H seal option, it uses FKM (Viton) elastomers that extend the operating temperature range up to 150 C, making it ideal for thermal processing environments. The built-in S magnet directly interfaces with AirTAC CMSE reed and DMSE electronic sensors along the three-sided sensor groove, ensuring reliable end-of-stroke detection. Field-adjustable air cushions at both ends allow you to fine-tune end-stop deceleration via a set screw, protecting tooling during rapid 30 mm strokes.
Airtac SE32 Standard Cylinder SE32X30SH Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X30SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X30SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X30SH Is Used
Injection Mold Ejection
Survives ambient heat near mold halves to eject small plastic parts, using the 30 mm stroke and Viton seal to withstand sustained 150 C temperatures.
Soldering Press
Applies precise 402 N clamping force at 0.5 MPa to hold electronic components against wave soldering fixtures without degrading in high-thermal zones.
Film Sealing Jaw
Cycles rapidly to crimp and seal packaging film on heated bars, relying on the field-adjustable air cushion to soften the 30 mm end stops.
Is the Airtac SE32 Standard Cylinder SE32X30SH the Right Cylinder?
When sizing this 32 mm bore, stepping down is not an option as this is the smallest available SE diameter. If your application requires more power, stepping up to the 40 mm bore yields 628 N of push at 0.5 MPa. Keep in mind that a standard SE cylinder relies on live air pressure to move; it will drift and cannot hold a load if air is exhausted or a valve centers. For positive holding, consider the BSE rod-lock variant.
As a true ISO 15552 cylinder, the SE32X30SH is dimensionally interchangeable with other ISO 15552 cylinders, serving as a drop-in replacement that reuses standard mounting hardware. To replicate this exact unit, specify the 32 mm bore, 30 mm stroke, PT1/8 port, basic mounting, the S magnet for CMSE/DMSE sensors, and the H FKM high-temperature seal.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X30SH FAQ
The 32 mm bore provides a push force of 402 N and a pull force of 345 N at 0.5 MPa. At 0.7 MPa, the push force is 563 N. The maximum push force is 82 kgf at 1.0 MPa.
Yes, the SE32X30SH features an H code FKM (Viton) seal, extending the operating temperature range up to 150 C. It also includes a built-in S magnet for CMSE and DMSE position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X30SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.