Airtac SE32 Standard Cylinder SE32X330S
The AirTAC Airtac SE32 Standard Cylinder SE32X330S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 330mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke330 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X330S
The AirTAC SE32X330S is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a 402 N push at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that simplifies mounting in tight machinery spaces.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration, softening impacts when cycling at speeds up to 800 mm/s.
Airtac SE32 Standard Cylinder SE32X330S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X330S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 330 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X330S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×330 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X330S Is Used
PCB Drill Bit Changer
Actuates tool-changing arms in CNC routers, using the 330 mm stroke to reach secondary tool racks while the compact profile saves machine space.
Small Package Diverter
Pushes lightweight parcels off a sorting line with 402 N of force, relying on DMSE electronic sensors to confirm full extension.
Carton Flap Folder
Folds minor flaps on automated boxing machines, where the adjustable cushion absorbs the kinetic energy of the fast 800 mm/s travel.
Is the Airtac SE32 Standard Cylinder SE32X330S the Right Cylinder?
This 32 mm bore generates 402 N of push force at 0.5 MPa. If your payload is lighter, stepping down is difficult as this is the smallest standard SE size, but if you need more thrust, the next size up is the 40 mm bore providing 628 N push. As a drop-in ISO 15552 replacement, it shares standard mounting interfaces and uses a PT1/8 port.
Because the 330 mm stroke is relatively long for a 12 mm rod, side loads can induce bending moments on the rod bearing; an external guide rail is recommended to prevent premature wear. Note that the adjustable air cushion only decelerates the piston near stroke end and does not hold the load—if air pressure is lost, the piston will drift.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X330S FAQ
At 0.5 MPa, it provides 402 N push and 345 N pull. At 0.7 MPa, the push increases to 563 N, with a maximum push of 82 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE32X330S is dimensionally interchangeable with any standard ISO 15552 profile cylinder. It shares standard mounting dimensions and uses a PT1/8 port, allowing for a direct retrofit without modifying the machine frame.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X330S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.