Airtac SE32 Standard Cylinder SE32X340S
The AirTAC Airtac SE32 Standard Cylinder SE32X340S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 340mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke340 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X340S
The AirTAC SE32X340S is a double-acting single-rod ISO 15552 profile cylinder engineered for compact automation. It delivers a 402 N push at 0.5 MPa, utilizing a 32 mm bore and a 340 mm stroke to drive lighter payloads. The square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant housing that simplifies mounting in tight machine cells.
This specific unit includes a built-in magnet (S option) for direct compatibility with AirTAC CMSE reed and DMSE electronic sensors. To protect the end caps during high-speed cycling up to 800 mm/s, it features field-adjustable pneumatic cushioning at both ends. You can tune the exhaust flow with a screw to soften hard end stops precisely for your load.
Airtac SE32 Standard Cylinder SE32X340S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X340S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 340 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X340S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×340 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X340S Is Used
PCB Depaneling Router
Provides the 402 N push needed to plunge a cutting spindle along a 340 mm path, separating printed circuit boards without stressing the substrate.
Sorter Diverter Gate
Actuates a lightweight routing flap over a 340 mm stroke to direct small parcels down secondary chutes at speeds up to 800 mm/s.
Film Feed Roll Tensioner
Travels 340 mm to position a packaging film roll, using the integrated magnet to trigger DMSE sensors for precise cut registration.
Is the Airtac SE32 Standard Cylinder SE32X340S the Right Cylinder?
Selecting the SE32X340S is ideal when you need the compact footprint of a 32 mm bore but require an extended 340 mm reach. If your application needs less force, there is no smaller standard ISO 15552 bore in this series, so you would instead look at compact non-ISO cylinders. If you need to step up the power, the next size up is the 40 mm bore, which provides a 628 N push at 0.5 MPa. Because this is a 340 mm stroke, the 12 mm piston rod experiences bending moments under side loads; always use an external guide rail to prevent rod-bearing wear.
As a true ISO 15552 cylinder, this model is dimensionally interchangeable with other ISO 15552 cylinders, allowing you to drop it into existing footprints using standard LB, FA, or TC mounting accessories. It uses a PT1/8 port. Note that while the adjustable cushioning decelerates the piston near stroke end, a plain SE cylinder does not hold its load if air pressure is lost; for dead-end holding, consider a BSE rod lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X340S FAQ
The SE32X340S provides a push force of 402 N and a pull force of 345 N at 0.5 MPa. At 0.7 MPa, the push force is 563 N. The maximum push force is 82 kgf when operated at the 1.0 MPa pressure limit.
Yes. The SE32X340S adheres strictly to the ISO 15552 / VDMA 24562 mounting interface, meaning it is dimensionally interchangeable with other ISO 15552 profile cylinders. You can drop it into existing machines using standard mounting hardware and PT1/8 ports.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X340S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.