Airtac SE32 Standard Cylinder SE32X65
The AirTAC Airtac SE32 Standard Cylinder SE32X65 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 65mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke65 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X65
The AirTAC SE32X65 is a double-acting single-rod ISO 15552 profile cylinder engineered for compact pneumatics, delivering 402 N of push force and 345 N of pull force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machine frames to save valuable space in tight assemblies.
This 32 mm bore unit features a 12 mm hard-chrome rod and a PT1/8 port. Field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration via a set screw, preventing harsh impacts during 30-800 mm/s cycling. Note this SKU is supplied without a built-in magnet, so it does not support CMSE or DMSE position sensing.
Airtac SE32 Standard Cylinder SE32X65 Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X65 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 65 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X65
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×65 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X65 Is Used
PCB Handling Ejectors
Uses the 402 N extend force and 65 mm stroke to push unpopulated circuit boards out of testing fixtures without damaging delicate traces.
Carton Flap Folders
Cycles at 30-800 mm/s to tuck small corrugated carton flaps prior to sealing, leveraging the smooth tie-rod-free profile for tight conveyor clearances.
Lab Sample Diverters
Actuates routing gates for diagnostic vial transport lines, where the adjustable end cushions provide gentle stops to prevent sample splashing.
Is the Airtac SE32 Standard Cylinder SE32X65 the Right Cylinder?
When sizing this 32 mm bore actuator, compare its 402 N push force against your actual load to ensure adequate thrust without oversizing. If your application requires less force, there is no smaller standard ISO 15552 bore in the AirTAC range, making this the most compact option. If you need significantly more power, stepping up to the 40 mm bore yields 628 N of push force at 0.5 MPa.
Keep in mind that a standard double-acting cylinder relies on continuous air pressure to hold its position; if air is lost or the valve is centered, the piston will drift, and an external guide or BSE rod-lock variant is required for secure load holding. At a 65 mm stroke, side-load bending is minimal, but the 12 mm rod thread still requires standard alignment to prevent premature seal wear. As a true ISO 15552 cylinder, it drops directly into existing footprints sharing standard LB, FA, and TC mounting hardware.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X65 FAQ
At 0.5 MPa, the SE32X65 provides 402 N of push force and 345 N of pull force. At 0.7 MPa, the push force increases to 563 N, with a maximum push capacity of 82 kgf at 1.0 MPa. It features a 12 mm rod, an M10x1.25 rod-end thread, and a PT1/8 port.
Yes, the SE32X65 is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can drop it into existing mounts sharing the standard interface, provided you use the default PT1/8 tapered port thread and do not require a position-sensing magnet on this specific SKU.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X65
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.