Airtac SE32 Standard Cylinder SE32X650S
The AirTAC Airtac SE32 Standard Cylinder SE32X650S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 650mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke650 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X650S
The AirTAC SE32X650S is a double-acting, single-rod ISO 15552 profile cylinder engineered for compact automation. It delivers 402 N of push force at 0.5 MPa and features a 650 mm stroke. The square extruded aluminum barrel eliminates external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly in tight machine envelopes.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable pneumatic cushioning at both ends allows you to tune deceleration, softening hard mechanical stops during high-speed cycling.
Airtac SE32 Standard Cylinder SE32X650S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X650S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 650 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X650S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×650 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X650S Is Used
PCB Depaneling Router
Actuates the cutting head carriage across 650 mm of travel, where the 402 N push force firmly positions the tooling while the magnet triggers DMSE sensors for precise edge alignment.
Small Parts Diverter
Pushes lightweight plastic housings off a 600 mm wide conveyor belt, utilizing the adjustable end cushions to prevent component damage during rapid 30-800 mm/s cycling.
Lab Sample Dispenser
Drives a volumetric syringe pump over a 650 mm stroke length, relying on the flush extruded aluminum profile to resist chemical splashes and fit inside crowded fume hoods.
Is the Airtac SE32 Standard Cylinder SE32X650S the Right Cylinder?
At 0.5 MPa, this 32 mm bore generates 402 N push and 345 N pull. If your process requires less force, you cannot step down from the 32 mm bore as it is the smallest in the SE series. If you need substantially more power, the next size up is the 40 mm bore, which provides 628 N push at 0.5 MPa.
Because this 650 mm stroke exceeds typical compact lengths, the Ø12 mm rod and rod-bearing face bending moments under lateral loads; always use an external guide to prevent side-load damage. For ISO 15552 dimensional retrofits, match the 32 mm bore, 650 mm stroke, PT1/8 port, and your required mounting accessory. Note that a plain SE does not hold loads safely upon air loss; if position locking is mandatory, specify a BSE rod-lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X650S FAQ
The 32 mm bore yields 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and a maximum of 82 kgf at 1.0 MPa. The operational speed range spans 30-800 mm/s.
Yes, the SE32X650S is dimensionally interchangeable with any standard ISO 15552 cylinder. However, it is a standard double-acting cylinder; the adjustable cushion only decelerates the piston and does not hold a load. For vertical load holding, use a BSE rod lock variant.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X650S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.