Airtac SE32 Standard Cylinder SE32X75S
The AirTAC Airtac SE32 Standard Cylinder SE32X75S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 75mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke75 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X75S
The AirTAC SE32X75S is a double-acting, single-rod ISO 15552 profile cylinder engineered for compact pneumatics. It delivers a push force of 402 N and a pull force of 345 N at 0.5 MPa, making it well-suited for lighter-duty automation. The extruded aluminum barrel design omits external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machine frames without snagging cables.
This 32mm bore unit includes a built-in magnet (-S) for direct compatibility with AirTAC CMSE reed and DMSE electronic sensors. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s rather than relying on a fixed rubber bumper.
Airtac SE32 Standard Cylinder SE32X75S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X75S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X75S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X75S Is Used
PCB Panel Ejection
Provides the precise 402N push required to eject populated printed circuit boards from an SMT line without damaging delicate traces.
Carton Flap Folding
Drives the mechanical arm that folds minor flaps on small product cartons, utilizing the 75mm stroke for rapid, compact actuation.
Lab Sample Sorting
Actuates the diverter gate on clinical analyzers to route sample tubes, benefiting from the flush profile to avoid trapping biohazards.
Is the Airtac SE32 Standard Cylinder SE32X75S the Right Cylinder?
With a 402 N push at 0.5 MPa, this model fits precise low-mass tasks. If you need less force, there is no smaller ISO 15552 bore in the SE range, but if your load demands more thrust, stepping up to the 40mm bore provides 628 N push. Remember that a standard SE does not hold its load when air is exhausted; if your fixture needs failsafe positioning, consider the BSE rod-lock variant. For retrofitting, this cylinder is dimensionally interchangeable with any ISO 15552 cylinder, using the standard PT1/8 port and M10x1.25 rod thread.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X75S FAQ
At 0.5 MPa, the SE32X75S delivers 402N push and 345N pull. At 0.7 MPa, the push force is 563N. The maximum push force is 82 kgf at 1.0 MPa operating pressure.
Yes. The SE32X75S is dimensionally interchangeable per ISO 15552 standards, meaning it shares identical mounting hole patterns and center distances. You can drop it in using your existing mounting hardware and PT1/8 pneumatic connections.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.