Airtac SE32 Standard Cylinder SE32X75SN
The AirTAC Airtac SE32 Standard Cylinder SE32X75SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 75mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke75 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X75SN
The AirTAC SE32X75SN is a double-acting single-rod profile cylinder built to the ISO 15552 / VDMA 24562 standard. It features a 32mm bore and a 75mm stroke, generating 402N of push force at 0.5 MPa. The extruded aluminum barrel design omits external tie rods, yielding a compact body that mounts flush against machine frames while resisting surface corrosion.
Equipped with a built-in magnet for CMSE and DMSE position sensing, and an NBR seal for standard operating temperatures, this unit incorporates field-adjustable air cushioning at both ends. You can tune the end-of-stroke deceleration via a setscrew to eliminate hard mechanical impacts during high-speed cycling.
Airtac SE32 Standard Cylinder SE32X75SN Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X75SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X75SN
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X75SN Is Used
Carton Flap Folding
Provides the precise 402N push at 0.5 MPa required to tuck minor flaps on automated case packers without crushing the corrugated board.
Light-Duty Part Ejection
Cycles at 30-800 mm/s to eject small plastic moulded parts from a press, using the adjustable cushion to soften the retraction stop.
Lab Sample Diverting
Uses the built-in magnet with DMSE electronic sensors to confirm piston position for diverting vials on a diagnostic analyser carousel.
Is the Airtac SE32 Standard Cylinder SE32X75SN the Right Cylinder?
At 402N push at 0.5 MPa, this 32mm bore is the smallest standard size in the SE range; stepping up to the 40mm bore increases the push force to 628N for heavier payloads. If your application requires holding a load statically when air pressure is removed, note that a standard SE cylinder will drift, so you should evaluate the BSE rod-lock variant. For this 75mm stroke, side-load bending on the rod bearing is minimal, but always verify the load is guided. As a dimensionally interchangeable ISO 15552 cylinder, it allows a direct drop-in replacement using existing PT1/8 port connections and standard mounting accessories.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X75SN FAQ
At 0.5 MPa, the push force is 402N and the pull force is 345N. At 0.7 MPa, the push force is 563N. The maximum push force is 82 kgf at 1.0 MPa.
No, the adjustable air cushion only decelerates the piston near the stroke end and does not lock the rod. If you need to hold a load without live pressure, consider the AirTAC BSE rod-lock series or an external pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X75SN
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.