Airtac SE32 Standard Cylinder SE32X75STC
The AirTAC Airtac SE32 Standard Cylinder SE32X75STC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 75mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke75 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X75STC
The AirTAC SE32X75STC is a double-acting single-rod ISO 15552 profile cylinder engineered for compact pneumatics. It delivers 402 N of push force at 0.5 MPa alongside 345 N of pull force. The square extruded aluminum barrel removes external tie rods entirely, yielding a flush exterior that simplifies tooling and resists corrosion. A built-in magnet enables position detection using CMSE reed or DMSE electronic sensors.
Field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration via a screw, preventing harsh impacts during high-speed 30-800 mm/s cycles. With a PT1/8 port, Ø12 mm rod, and M10x1.25 thread, this unit serves as a dimensionally interchangeable drop-in replacement for any standard ISO 15552 cylinder.
Airtac SE32 Standard Cylinder SE32X75STC Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X75STC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X75STC
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X75STC Is Used
PCB Board Clamping
Provides 402 N of push force to secure delicate printed circuit boards during automated soldering or component placement without damaging the substrate.
Carton Flap Folding
Uses the 75 mm stroke and adjustable cushioning to fold cardboard flaps smoothly on high-speed packaging lines, preventing harsh end-stop impacts.
Lab Sample Sorting
Handles the precise positional transfer of test tubes or vials into analytical centrifuges, relying on the DMSE electronic sensor feedback for exact timing.
Is the Airtac SE32 Standard Cylinder SE32X75STC the Right Cylinder?
With a 402 N push at 0.5 MPa, this 32 mm bore is ideal for light-duty handling. If your application requires less force, the next size down is the 25 mm bore offering 245 N push, while stepping up to the 40 mm bore provides 628 N push for heavier loads. This configuration includes a TC centre trunnion mount and an -S magnet for CMSE/DMSE sensors. Because it is a standard double-acting cylinder, it cannot hold a load if air pressure drops; use a BSE rod lock for fail-safe positioning. At 75 mm stroke, side-load bending is minimal, but always verify rod-bearing loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X75STC FAQ
The SE32X75STC delivers a push force of 402 N and a pull force of 345 N at 0.5 MPa. At 0.7 MPa, the push force is 563 N, with a maximum push of 82 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE32X75STC is dimensionally interchangeable per ISO 15552 standards. It features a standardized mounting footprint and a PT1/8 port, allowing it to serve as a direct drop-in replacement for other ISO 15552 profile cylinders using the TC mounting accessory.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X75STC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.