Airtac SE32 Standard Cylinder SE32X90S
The AirTAC Airtac SE32 Standard Cylinder SE32X90S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 90mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke90 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X90S
The AirTAC SE32X90S is a double-acting, single-rod ISO 15552 profile cylinder delivering a 402 N push force at 0.5 MPa. Its extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensing. Field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration, preventing hard impacts during rapid 30-800 mm/s cycles.
Airtac SE32 Standard Cylinder SE32X90S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X90S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 90 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X90S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X90S Is Used
PCB Depaneling Saw
Provides the 402 N push and 90 mm travel needed to advance circuit boards through a depaneling routing saw at a controlled speed.
Lab Sample Dispenser
Actuates a 90 mm stroke to meter precise fluid volumes into vials, using the -S magnet to trigger DMSE sensors for fill confirmation.
Small Part Ejector
Kicks lightweight plastic molded parts out of an indexing press, relying on adjustable cushions to soften the 90 mm retract stop.
Is the Airtac SE32 Standard Cylinder SE32X90S the Right Cylinder?
Generating 402 N of push at 0.5 MPa, this 32 mm bore suits light-duty positioning. If your load demands less force, dropping to a 25 mm bore reduces footprint, while stepping up to a 40 mm bore provides a 628 N push for heavier resistance. As a standard ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement sharing standardized mounting hardware.
The integrated -S magnet enables CMSE and DMSE sensor feedback for automated sequencing. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not lock the load. If unpowered drift risks dropping a part, specify a BSE rod lock variant instead.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X90S FAQ
The 32 mm bore generates 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and a maximum 82 kgf at 1.0 MPa. It uses a PT1/8 port and a 12 mm rod with an M10x1.25 thread.
Yes, it is dimensionally interchangeable per ISO 15552, allowing a drop-in retrofit with shared mounting brackets. However, it will drift if air pressure is lost; the adjustable cushion only decelerates the piston near stroke end and does not lock the load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X90S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.