Airtac SE40 Standard Cylinder SE40BX80SH
The AirTAC SE40 Standard Cylinder SE40BX80SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 80mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ40 mm
- Stroke80 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM12×1.25
- CushionAdjustable, 30 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE40 Standard Cylinder SE40BX80SH
The AirTAC SE40BX80SH is a double-acting single-rod ISO 15552 profile cylinder engineered for aggressive environments. It delivers 628 N of push force and 528 N of pull force at 0.5 MPa. Equipped with a SUS304 stainless steel rod and FKM Viton seals, this unit reliably operates in temperatures up to 150 C, making it highly resistant to chemical washdowns and thermal degradation.
Built on a square extruded aluminum barrel without external tie rods, the body is inherently compact and corrosion-resistant. The integrated magnet (-S) directly supports AirTAC CMSE reed and DMSE electronic position sensors, while field-adjustable air cushions at both ends allow you to fine-tune end-of-stroke deceleration to eliminate hard mechanical impacts.
Airtac SE40 Standard Cylinder SE40BX80SH Technical Specifications
| Model | Airtac SE40 Standard Cylinder SE40BX80SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø40mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE40 Standard Cylinder SE40BX80SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE40 Standard Cylinder SE40BX80SH Is Used
Food Packaging Equipment
With a SUS304 rod and 150 C FKM seals, this 628 N cylinder withstands thermal sterilization cycles while actuating sealing jaws on vertical form-fill machines.
Bottling Line Diverter
The 80 mm stroke precisely routes plastic containers between processing lanes, utilizing the corrosion-resistant stainless rod to survive caustic washdowns.
Chemical Lab Dispenser
Provides consistent 528 N retraction force to meter reagents, with the Viton seal preventing structural degradation when exposed to aggressive solvent vapors.
Is the Airtac SE40 Standard Cylinder SE40BX80SH the Right Cylinder?
If your application requires less force, stepping down to a 32 mm bore yields 402 N of push at 0.5 MPa, whereas scaling up to a 50 mm bore provides 982 N. As a true ISO 15552 profile cylinder, this 40 mm bore with an 80 mm stroke, PT1/4 port, and Viton seal serves as a direct dimensional replacement for competing ISO 15552 cylinders. Remember that the adjustable air cushion only decelerates the piston near stroke end; it does not hold a load. If pneumatic pressure is lost, the rod drifts, requiring an external guide or pilot-operated check valve for position holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE40 Standard Cylinder SE40BX80SH FAQ
At 0.5 MPa, the SE40BX80SH provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa.
Yes. The SE40BX80SH features a standardized ISO 15552 / VDMA 24562 mounting interface, making it dimensionally interchangeable with other ISO 15552 profile cylinders. You can drop it directly into existing mounting hardware without modifying the fixture.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE40 Standard Cylinder SE40BX80SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.