
The AirTAC SE40 Standard Cylinder SE40X100CB is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 100mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X100CB is a double-acting single-rod ISO 15552 profile cylinder engineered for pivoting motion. It delivers 628 N of push force and 528 N of pull force at 0.5 MPa, utilizing a 16 mm rod and a PT1/4 port. The CB mounting style integrates a double clevis eye directly into the rear cap, making it well-suited for articulated mechanisms that require angular alignment during the stroke.
Unlike traditional tie-rod designs, its square extruded aluminum barrel lacks external hardware, offering a flush, corrosion-resistant exterior that simplifies mounting. The cylinder features field-adjustable pneumatic cushioning at both ends, allowing you to tune the end-of-stroke deceleration via a set screw to eliminate hard metal impacts. This SKU does not include a position sensor magnet, so it cannot host CMSE or DMSE switches without modification.
| Model | Airtac SE40 Standard Cylinder SE40X100CB |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the pivoting arms of cardboard case erectors where 628 N of push force smoothly folds carton flaps at high cycle rates.
Controls the angular movement of conveyor sorting gates, utilizing the CB clevis mount to accommodate the arc of the routing flap.
Positions fluidic sampling probes on diagnostic analyzers, benefiting from the compact tie-rod-free barrel for tight cell enclosures.
If your mechanism requires less force, stepping down to the 32 mm bore yields 402 N of push at 0.5 MPa, while moving up to the 50 mm bore provides 982 N for heavier pivoting loads. Because this is a double-acting cylinder, it cannot hold a load in place if air pressure is lost or the valve is centered; the piston will drift. For applications needing secure position holding, consider the BSE rod-lock variant or an external pilot-operated check valve.
As a true ISO 15552 cylinder, it is dimensionally interchangeable with other standard profile cylinders, ensuring a direct retrofit for existing mounting hardware. When ordering, confirm your need for the CB double clevis mount, a 100 mm stroke, and the PT1/4 port. Since the stroke is 100 mm, side-load stress on the rod bearing is minimal, but always ensure the clevis pin is adequately supported to prevent binding.
Quick checklist
The SE40X100CB provides 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. It features a 16 mm rod with an M12x1.25 thread and a PT1/4 air port.
Yes, the SE40X100CB is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint and can serve as a direct replacement for other ISO 15552 profile cylinders without altering your equipment.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.