verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE40 Standard Cylinder SE40X100H

The AirTAC SE40 Standard Cylinder SE40X100H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 100mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ40 mm
  • Stroke100 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM12×1.25
  • CushionAdjustable, 30 mm
$64.43 $71.93Save 10% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE40 stroke, mounting and version on one page All SE40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE40 Standard Cylinder SE40X100H

The AirTAC SE40X100H is a double-acting, single-rod ISO 15552 profile cylinder engineered for high-temperature actuation. Equipped with a Viton (FKM) seal, it operates reliably up to 150 C, expanding the standard -20 to +70 C range for hot environments. It delivers 628 N of push force and 528 N of pull force at 0.5 MPa, making it suited for compact mid-force machinery.

The extruded aluminum barrel omits external tie rods, yielding a smooth, corrosion-resistant profile that mounts flush against frames. Field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration via a screw, softening hard impacts at high cycle rates. This specific SKU lacks a built-in magnet, so it does not support CMSE or DMSE position sensing without modification.

Airtac SE40 Standard Cylinder SE40X100H Technical Specifications

ModelAirtac SE40 Standard Cylinder SE40X100H
SeriesSE ISO 15552 profile cylinder
Bore sizeØ40 mm
Stroke100 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM12×1.25
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE40 Standard Cylinder SE40X100H

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
40Bore size in mm.
×100Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE40 Standard Cylinder SE40X100H Is Used

science

Injection Mold Ejection

Survives ambient heat near platens, using the FKM seal to deliver 628 N push at 0.5 MPa for part ejection cycles up to 150 C.

packaging

Heat Shrink Wrapper Jaws

Actuates sealing jaws in close proximity to shrink-tunnels, where the Viton seal resists thermal degradation over continuous 100 mm strokes.

factory

Hot Glue Dispense Head

Positions dispense nozzles over packaging lines, relying on the adjustable air cushion to decelerate the rod smoothly at 30-800 mm/s.

Is the Airtac SE40 Standard Cylinder SE40X100H the Right Cylinder?

At 0.5 MPa, this 40 mm bore generates 628 N of push force. If your application requires less force, you can step down to the 32 mm bore, which provides 402 N of push at 0.5 MPa. If you need more thrust, stepping up to the 50 mm bore yields 982 N of push at 0.5 MPa. The PT1/4 port and 100 mm stroke match standard ISO 15552 mounting dimensions, allowing a direct replacement for other ISO 15552 cylinders using identical hardware.

Because this is a double-acting cylinder, it will not hold a load if air pressure is lost or the valve is centered; the piston will drift. For position-holding safety, consider the BSE rod-lock variant or an external pilot-operated check valve. The 100 mm stroke is below the 300 mm threshold, so side-load bending is minimal, though the 16 mm rod still requires standard alignment.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE40 Standard Cylinder SE40X100H FAQ

This 40 mm bore cylinder provides 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. The H designation indicates a Viton (FKM) seal, extending the operating temperature range up to 150 C.

Yes, it shares standard ISO 15552 / VDMA 24562 mounting interface dimensions for direct interchangeability. However, this specific SKU lacks the -S magnet code, meaning it cannot support AirTAC CMSE or DMSE position sensors out of the box.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE40 Standard Cylinder SE40X100H

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE40X100H and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.