
The AirTAC SE40 Standard Cylinder SE40X100SFTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 100mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X100SFTC is a double-acting single-rod ISO 15552 profile cylinder engineered for mid-range actuation, delivering 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This clean profile simplifies sensor placement along the three integrated grooves.
Equipped with a built-in magnetic ring (-S), this unit interfaces directly with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed cycling. The integrated FTC center trunnion mount provides pivotal support for dynamic articulation.
| Model | Airtac SE40 Standard Cylinder SE40X100SFTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 628 N push and 100 mm travel needed to fold corrugated cardboard flaps on continuous packaging lines without crushing the material.
Leverages the FTC trunnion mount to articulate a diverter arm, smoothly routing heavy pallets between conveyor belts at high cycling speeds.
Uses the adjustable end cushions to decelerate rapid ejection strokes on CNC secondary operations, protecting delicate machined aluminum parts from marring.
Selecting this 40 mm bore makes sense when your application requires 628 N push at 0.5 MPa. If you need less force, stepping down to the 32 mm bore yields 402 N push; conversely, scaling up to the 50 mm bore provides 982 N push. This model includes the FTC center trunnion accessory, a PT1/4 port, and the -S magnet for CMSE/DMSE switches, ensuring a direct replacement for any ISO 15552 cylinder footprint.
Remember that a standard SE cylinder drifts when air pressure is lost or the valve centers—the adjustable cushion only decelerates the piston near stroke end and does not act as a locking brake. If your fixture must hold a vertical load safely without live pressure, integrate an external pilot-operated check valve or specify a BSE rod-lock variant.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N push and 528 N pull. At 0.7 MPa, the push increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE40X100SFTC is dimensionally interchangeable per ISO 15552. You can drop it directly into existing mounting footprints and use standard FTC trunnion hardware. The -S magnet also allows seamless integration with AirTAC CMSE or DMSE position sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.