
The AirTAC SE40 Standard Cylinder SE40X100SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 100mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X100SH is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a 628 N push at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
Equipped with a Viton (FKM) seal, this unit reliably operates in ambient temperatures up to 150 C. The integrated -S magnet interfaces directly with AirTAC CMSE reed and DMSE electronic sensors, while the field-adjustable air cushioning at both ends lets you fine-tune end-of-stroke deceleration to dampen hard impacts.
| Model | Airtac SE40 Standard Cylinder SE40X100SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Applies 628 N of clamping force on packaging film jaws, where the FKM seal survives continuous radiant heat up to 150 C without degrading.
Drives a 100 mm stroke routing gate on a conveyor line, using the integrated magnet with DMSE sensors to confirm divert position.
Ejects hot plastic parts from mold cavities, leveraging the tie-rod-free extruded profile to fit within tight press tooling.
Choosing this 40 mm bore makes sense when you need 628 N of push force at 0.5 MPa. If your load is lighter, stepping down to the 32 mm bore yields 402 N push; if you require more authority, the 50 mm bore provides 982 N push. Because this is a standard ISO 15552 footprint, it serves as a direct dimensional replacement for other ISO 15552 cylinders, matching the PT1/4 port, 100 mm stroke, and standard mounting accessories.
Remember that the adjustable pneumatic cushion only decelerates the piston near stroke end and does not lock the rod. If your process loses air pressure, the cylinder will drift, so you must add a BSE rod lock or external pilot-operated check valve to hold suspended loads safely in place.
Quick checklist
At 0.5 MPa it provides 628 N push and 528 N pull. At 0.7 MPa the push increases to 879 N, with a maximum push of 128 kgf at 1.0 MPa. The operating speed ranges from 30-800 mm/s.
Yes. It shares the exact ISO 15552 mounting interface and PT1/4 port size for direct interchangeability, but the H designation means it uses a Viton (FKM) seal rated for 150 C, making it suitable for high-temperature environments where standard seals fail.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.