
The AirTAC SE40 Standard Cylinder SE40X100SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 100mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X100SN is a double-acting single-rod profile cylinder built to the ISO 15552 / VDMA 24562 standard. It features a square extruded aluminum barrel without external tie rods, making it compact and highly resistant to corrosion while allowing flush mounting on machinery. Delivering 628 N of push force and 528 N of pull force at 0.5 MPa, it is equipped with an NBR seal and a built-in magnet for position sensing.
Unlike fixed rubber bumpers, this model incorporates a field-adjustable pneumatic cushion at both ends, allowing technicians to tune the end-of-stroke deceleration via a screw to minimize impact wear at operating speeds up to 800 mm/s. The integrated magnet supports AirTAC CMSE reed and DMSE electronic sensors, which slide directly into the extruded barrel's sensor grooves for rapid deployment.
| Model | Airtac SE40 Standard Cylinder SE40X100SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 628 N push at 0.5 MPa required to snap corrugated cartons open, using the 100 mm stroke to cycle rapidly without overstressing the flimsy material.
Shifts lightweight packages between sorting lanes on a conveyor line, relying on the NBR seals and built-in magnet for reliable DMSE sensor feedback.
Accurately pushes sample racks into testing position, utilizing the adjustable pneumatic cushion to prevent sudden stops that could spill liquids.
If your application requires less force, stepping down to the 32 mm bore yields 402 N of push at 0.5 MPa, whereas moving up to the 50 mm bore provides 982 N. This 40 mm bore utilizes a PT1/4 port and a 16 mm rod, striking a balance between speed and mid-range thrust. Because the stroke is 100 mm, side-load stress on the rod bearing is minimal, but always verify load alignment to prevent premature seal wear.
As a true ISO 15552 profile cylinder, it is dimensionally interchangeable with other ISO 15552 cylinders, ensuring a seamless retrofit using existing mounting hardware like LB foot brackets or FA front flanges. Note that the adjustable air cushion only decelerates the piston near the stroke end; it does not hold the load if air pressure is lost. For position holding without live pressure, consider the BSE rod lock variant.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N, with a maximum push of 128 kgf at 1.0 MPa. Operating pressure ranges from 0.15-1.0 MPa, and the speed range is 30-800 mm/s.
Yes, the SE40X100SN is dimensionally interchangeable per the ISO 15552 / VDMA 24562 standard, meaning it shares the exact mounting footprint, PT1/4 port size, and 100 mm stroke dimensions of other ISO 15552 profile cylinders, allowing a direct replacement.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.