
The AirTAC SE40 Standard Cylinder SE40X1080S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 1080mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X1080S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding automation tasks. At 0.5 MPa, it generates 628 N of push force and 528 N of pull force, utilizing a 16 mm hard-chrome rod with an M12x1.25 thread. Because this 1080 mm stroke exceeds the standard 1200 mm maximum for a 40 mm bore, it is supplied as a made-to-order assembly.
The extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant profile that mounts flush while exposing sensor grooves on three sides. The integrated -S magnet directly supports AirTAC CMSE reed and DMSE electronic position switches, and the field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration for high-speed 30-800 mm/s cycles.
| Model | Airtac SE40 Standard Cylinder SE40X1080S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 1080 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×1080 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Handles high-speed 30-800 mm/s actuation across a 1080 mm stroke to push parcels onto secondary chutes, relying on the 628 N push force to redirect heavy cardboard boxes.
Applies 528 N of pull force to clamp sheet metal during a multi-stage bending process, using the -S magnet to confirm full retraction via DMSE electronic sensors.
Drives a 1080 mm safety gate at material entry points, utilizing the field-adjustable end cushions to soften hard stops during rapid 800 mm/s cycles.
For sizing flexibility, stepping down to a 32 mm bore reduces the 0.5 MPa push to 402 N, while moving up to a 50 mm bore increases it to 982 N. Because this is a plain double-acting cylinder, it cannot hold a load if air pressure drops; if your application requires static holding, consider the BSE rod lock variant. At 1080 mm of unsupported stroke, the 16 mm rod is highly susceptible to bending under side loads, so an external guide rail is strongly recommended to prevent premature bearing wear. As a true ISO 15552 cylinder, it serves as a direct replacement sharing standard mounting interface dimensions and PT1/4 ports.
Quick checklist
The SE40X1080S delivers 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. It features a PT1/4 port and operates at speeds of 30-800 mm/s.
Yes, the SE40X1080S shares standard ISO 15552 / VDMA 24562 mounting interface dimensions, making it a direct replacement for other ISO 15552 profile cylinders. The built-in -S magnet also ensures seamless integration with AirTAC CMSE and DMSE position sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.