verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE40 Standard Cylinder SE40X1200

The AirTAC SE40 Standard Cylinder SE40X1200 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 1200mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ40 mm
  • Stroke1200 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM12×1.25
  • CushionAdjustable, 30 mm
$178.16 $185.66Save 4% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE40 stroke, mounting and version on one page All SE40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE40 Standard Cylinder SE40X1200

The AirTAC SE40X1200 is a double-acting, single-rod ISO 15552 profile cylinder engineered for long-stroke linear motion. It delivers 628 N of push force at 0.5 MPa and 879 N at 0.7 MPa, utilizing a 40 mm bore and a 1200 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies sensor placement along its three integrated grooves.

Because this specific SKU lacks the -S magnet suffix, it does not support AirTAC CMSE or DMSE position sensing out of the box. Field-adjustable pneumatic cushioning at both ends allows technicians to tune the end-of-stroke deceleration via a set screw, softening impacts when cycling payloads at speeds up to 800 mm/s.

Airtac SE40 Standard Cylinder SE40X1200 Technical Specifications

ModelAirtac SE40 Standard Cylinder SE40X1200
SeriesSE ISO 15552 profile cylinder
Bore sizeØ40 mm
Stroke1200 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM12×1.25
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE40 Standard Cylinder SE40X1200

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
40Bore size in mm.
×1200Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE40 Standard Cylinder SE40X1200 Is Used

conveyor_belt

Pallet Transfer Pusher

Uses the 1200 mm stroke to push packaged pallets cleanly from a high-speed wrapping line onto an adjacent roller conveyor, relying on the 628 N push force to overcome initial friction.

warehouse

Vertical Lift Gate Actuator

Raises and lowers a 1.2 meter security gate on a packaging cell; the adjustable end cushions absorb the kinetic energy of the falling gate at the bottom of the stroke to prevent mechanical shock.

straighten

Long-Stroke Sheet Aligner

Sweeps corrugated cardboard sheets into a stacking register, utilizing the full 1200 mm extension to accommodate wide format materials without needing a multi-stage telescopic cylinder.

Is the Airtac SE40 Standard Cylinder SE40X1200 the Right Cylinder?

When sizing this actuator, compare its 628 N push at 0.5 MPa against adjacent bores: the SE32 provides a smaller 402 N push, while the SE50 steps up to 982 N. This 40 mm bore hits a reliable middle ground for moderate loads. For direct retrofits, match the 40 mm bore, 1200 mm stroke, PT1/4 port thread, and your required ISO 15552 mounting accessory.

At 1200 mm of stroke, the 16 mm rod and internal bearing face significant bending moments under side loads; an external guide rail is strongly recommended to prevent premature seal wear. Note that a plain SE cylinder cannot hold a load if air pressure drops—the adjustable cushion only decelerates the piston near stroke end, so add a BSE rod lock if static holding is required.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE40 Standard Cylinder SE40X1200 FAQ

At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push capacity is 128 kgf at 1.0 MPa. The 1200 mm stroke is the maximum standard stroke available for this bore size.

Yes, its standardized ISO 15552 mounting dimensions make it a direct replacement for other 40 mm profile cylinders. However, it is a double-acting cylinder without a rod lock; if air is lost, the piston will drift. The adjustable air cushion only decelerates the piston near the end of stroke and cannot hold a vertical load.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE40 Standard Cylinder SE40X1200

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE40X1200 and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.