Airtac SE40 Standard Cylinder SE40X150SCBCR
The AirTAC SE40 Standard Cylinder SE40X150SCBCR is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 150mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ40 mm
- Stroke150 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM12×1.25
- CushionAdjustable, 30 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE40 Standard Cylinder SE40X150SCBCR
The AirTAC SE40X150SCBCR is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly against machine frames. The integrated magnet supports position sensing.
This 40 mm bore unit uses a PT1/4 port and a 16 mm hard-chrome rod to achieve a 150 mm stroke. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration, preventing harsh impacts when cycling at speeds up to 800 mm/s. The CB double clevis mount is included for pivoting installations.
Airtac SE40 Standard Cylinder SE40X150SCBCR Technical Specifications
| Model | Airtac SE40 Standard Cylinder SE40X150SCBCR |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø40mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE40 Standard Cylinder SE40X150SCBCR
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE40 Standard Cylinder SE40X150SCBCR Is Used
Carton Flap Folding
Drives the mechanical arms that tuck and seal corrugated box flaps, utilizing the 628 N push force to overcome cardboard stiffness at high cycling speeds.
Pallet Diverter Gate
Actuates a pivoting CB-mounted deflector plate to route medium-weight pallets onto a secondary packaging line without stalling the main conveyor flow.
PCB Test Fixture
Lowers an electronic test probe array onto printed circuit boards, relying on the DMSE sensor signal to confirm the 150 mm stroke is fully extended before initiating the electrical check.
Is the Airtac SE40 Standard Cylinder SE40X150SCBCR the Right Cylinder?
Select this 40 mm bore when an application requires 628 N push at 0.5 MPa. If your payload is lighter, stepping down to the 32 mm bore yields 402 N push; if you need more authority, the 50 mm bore provides 982 N push. Because this cylinder uses a CB clevis mount, ensure your mating joint accommodates the pivot pin. The -S magnet enables CMSE reed or DMSE electronic sensors for precise end-position confirmation.
Remember that the adjustable air cushion only decelerates the piston near stroke end and does not lock the rod. If air pressure drops, the cylinder will drift and cannot hold a load. For position-holding safety, consider a BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE40 Standard Cylinder SE40X150SCBCR FAQ
At 0.5 MPa, this 40 mm bore cylinder provides 628 N push and 528 N pull force. At 0.7 MPa, the push force is 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE40X150SCBCR is dimensionally interchangeable per ISO 15552. You can drop it in as a replacement for other ISO 15552 profile cylinders with a 40 mm bore and 150 mm stroke, matching the standard PT1/4 port and CB mounting interface.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE40 Standard Cylinder SE40X150SCBCR
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.