
The AirTAC SE40 Standard Cylinder SE40X15S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 15mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X15S is a double-acting single-rod ISO 15552 profile cylinder engineered for compact actuation, delivering 628 N of push force at 0.5 MPa. Its 15 mm stroke is a non-standard made-to-order length, purpose-built for applications requiring extremely tight retraction. The square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that simplifies mounting in confined machinery.
Equipped with a built-in magnet (S option), this unit supports AirTAC CMSE reed and DMSE electronic position sensors along the three integrated sensor grooves. The field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a set screw, ensuring smooth stops even at the 30-800 mm/s operating speed range.
| Model | Airtac SE40 Standard Cylinder SE40X15S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 15 mm stroke to rapidly eject small stamped metal pins from a die, relying on the 628 N push force to overcome die friction.
Executes quick, short-throw folding of corrugated carton flaps on a packaging line, where the compact 40 mm profile avoids interfering with product flow.
Applies precise 528 N pull force to seat a bearing into a housing, using the adjustable cushion to prevent impact damage at the end of the short 15 mm retract.
Choosing this 40 mm bore depends on needing high force in a minimal footprint; if your application requires less thrust, stepping down to the 32 mm bore yields 402 N of push at 0.5 MPa, while scaling up to the 50 mm bore provides 982 N. Because the 15 mm stroke is non-standard, expect a made-to-order lead time. As a true ISO 15552 cylinder, it serves as a direct dimensional replacement for other ISO 15552 profile cylinders, utilizing standard mounting accessories and a PT1/4 port.
Note that a plain SE cylinder does not hold its load when air pressure is lost or the valve is centered; the piston will drift. If your short-stroke clamping or lifting task requires strict position holding without live pressure, consider the BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push capacity is 128 kgf at 1.0 MPa. It operates at pressures from 0.15-1.0 MPa with a speed range of 30-800 mm/s.
Yes, the SE40X15S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders, matching the PT1/4 port and standard mounting hardware. The built-in magnet also allows you to mount AirTAC CMSE or DMSE sensors directly into the body grooves.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.