
The AirTAC SE40 Standard Cylinder SE40X180 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 180mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X180 is a double-acting single-rod ISO 15552 profile cylinder, delivering 628 N of push force and 528 N of pull force at 0.5 MPa. It features a 40 mm bore, a 180 mm stroke, and a PT1/4 port. This actuator uses a square extruded aluminum barrel without external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
The cylinder incorporates field-adjustable air cushioning at both ends, allowing you to tune end-of-stroke deceleration via a set screw to soften hard impacts during high-speed cycling. This specific SKU is built without a magnet, meaning it does not support CMSE or DMSE electronic position sensing out of the box.
| Model | Airtac SE40 Standard Cylinder SE40X180 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 180 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×180 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 628 N of push force at 0.5 MPa to secure aluminum castings against CNC machining stops during milling operations.
Uses the 180 mm stroke to extend folding arms across corrugated cardboard packaging lines, timing flap closure before case sealing.
Actuates routing gates on modular belt conveyors, leveraging the no-tie-rod profile to mount flush within tight transfer zones.
When sizing this 40 mm bore actuator, compare its 628 N push at 0.5 MPa against the 32 mm bore (402 N) for lighter clamping tasks, or step up to the 50 mm bore (982 N) if your mechanism requires greater thrust. Because this is a double-acting cylinder, it relies on continuous live air pressure to hold a load; if air is lost or the valve is centered, the piston will drift and cannot maintain position without an external pilot-operated check valve or a BSE rod-lock variant.
With its 180 mm stroke, this model falls under the standard maximum stroke limit of 1200 mm. The 16 mm rod and M12x1.25 thread handle moderate side loads, but for any unsupported stroke exceeding 300 mm, you should incorporate an external guide rail to prevent rod-bearing bending. Its standardized ISO 15552 mounting dimensions ensure it serves as a direct replacement for other ISO 15552 profile cylinders, sharing standard FA, LB, or TC mounting hardware.
Quick checklist
The SE40X180 generates 628 N of push force and 528 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No, the standard SE40X180 is a double-acting cylinder and will drift if air is lost or the directional valve is centered. The adjustable air cushion at both ends only decelerates the piston near the stroke end; it does not act as a brake or lock. For position holding, consider a BSE rod lock variant.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.