
The AirTAC SE40 Standard Cylinder SE40X185 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 185mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X185 is a double-acting single-rod profile cylinder built to the ISO 15552 / VDMA 24562 standard. It features a 40 mm bore and a 185 mm stroke, generating 628 N of push force at 0.5 MPa and 879 N at 0.7 MPa. The square extruded aluminum barrel eliminates external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
This SKU ships without a piston magnet, so it does not support CMSE or DMSE electronic position sensing out of the box. Field-adjustable pneumatic cushioning at both ends allows you to tune the end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s. The fluid medium is filtered 40 um air, operating reliably between 0.15 and 1.0 MPa.
| Model | Airtac SE40 Standard Cylinder SE40X185 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 185 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×185 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a routing flap on a logistics conveyor, using the 185 mm stroke to swing the gate fully open and redirect cartons at high speed.
Maintains precise downward pressure on a shrink-wrap film roll, utilizing the 628 N push force to prevent slack during high-speed packaging cycles.
Pushes machined aluminum parts out of a CNC fixture, relying on the adjustable cushion to bring the rod to a smooth stop without marring the finish.
Selecting this 40 mm bore makes sense when your application requires roughly 628 N of push at 0.5 MPa. If you need less force, stepping down to the 32 mm bore yields 402 N of push; stepping up to the 50 mm bore provides 982 N. Because this specific SKU lacks the S magnet code, you cannot mount reed or solid-state sensors directly to the groove for end-of-stroke confirmation.
With a 185 mm stroke, the 16 mm rod and M12x1.25 thread provide a robust interface, though you should still verify side-load limits if the load is unsupported. The PT1/4 porting and ISO 15552 mounting dimensions make it a direct replacement for other ISO 15552 profile cylinders, allowing you to reuse existing FA front flanges or LB foot brackets. Note that the adjustable air cushion only decelerates the piston near the end of travel; it does not hold the load if air pressure is lost.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder outputs 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf at 1.0 MPa. It operates at speeds ranging from 30 to 800 mm/s.
Yes, the SE40X185 is dimensionally interchangeable with any standard ISO 15552 profile cylinder. You can reuse your existing mounting hardware and PT1/4 pneumatic fittings. Because this specific SKU lacks a piston magnet, ensure you do not require position sensing for your retrofit.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.