
The AirTAC SE40 Standard Cylinder SE40X185S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 185mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X185S is a double-acting single-rod profile cylinder built to the ISO 15552 standard. It features a 40 mm bore and a 185 mm stroke, generating 628 N of push force and 528 N of pull force at 0.5 MPa. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This specific unit includes a built-in magnet (-S) for position sensing with AirTAC CMSE reed or DMSE electronic switches. To manage kinetic energy, field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, preventing hard impacts during high-speed 30-800 mm/s cycles.
| Model | Airtac SE40 Standard Cylinder SE40X185S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 185 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×185 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 628 N push at 0.5 MPa needed to fold corrugated cardboard flaps on high-speed packaging lines, utilizing the 185 mm stroke to clear the machine during retraction.
Actuates a routing diverter arm to sort parcels; the -S magnet works with DMSE electronic sensors to confirm gate position before product arrival, while adjustable cushions soften the 185 mm stroke ends.
Holds electronic test fixtures in place with 528 N of pull force, where the no-tie-rod extruded profile allows space-constrained mounting directly beneath the testing station.
Selecting this 40 mm bore makes sense when your application requires roughly 628 N of push at 0.5 MPa. If you need less force, stepping down to the 32 mm bore yields 402 N of push; stepping up to the 50 mm bore provides 982 N. Because this is a standard double-acting cylinder, it will drift if air pressure is lost or the valve centers—use a BSE rod lock variant if the load must be mechanically held. Its standardized ISO 15552 mounting dimensions ensure it drops directly into existing foot, flange, or trunnion hardware.
With a 185 mm stroke, the 16 mm rod and M12x1.25 thread provide solid rigidity, but always verify side loading. For strokes of 300 mm or longer, adding an external guide rail becomes critical to prevent rod-bearing bending and premature seal wear.
Quick checklist
At 0.5 MPa, the SE40X185S generates 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE40X185S is dimensionally interchangeable per ISO 15552 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders, matching the 40 mm bore, 185 mm stroke, PT1/4 port, and standard mounting accessories without altering the machine footprint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.