
The AirTAC SE40 Standard Cylinder SE40X190 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 190mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X190 is a double-acting single-rod ISO 15552 profile cylinder with a 40 mm bore and a made-to-order 190 mm stroke. It delivers a theoretical push force of 628 N at 0.5 MPa, extending to 879 N at 0.7 MPa, making it well-suited for mid-range actuation tasks.
Built with an extruded aluminum barrel that eliminates external tie rods, this design offers a compact footprint and flush mounting convenience. The field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration via a set screw, protecting the mechanism from hard impacts. Note that this specific SKU lacks a built-in magnet, so it does not support CMSE or DMSE electronic position sensing without modification.
| Model | Airtac SE40 Standard Cylinder SE40X190 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 190 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×190 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a routing flap on a logistics sorting line, utilizing the 190 mm stroke to clear standard totes while providing 628 N of push force at 0.5 MPa.
Drives the mechanical arms that fold minor flaps on a continuous carton erector, relying on the adjustable end cushions to prevent tearing during high-speed cycling.
Maintains dynamic tension on a fabric feed roller, using the 879 N extend force at 0.7 MPa to compensate for material roll diameter changes.
When sizing this 40 mm bore actuator, compare its 628 N push at 0.5 MPa against your actual load requirements. If you need less force and a smaller footprint, stepping down to the 32 mm bore yields 402 N of push. Conversely, if your payload demands more thrust, stepping up to the 50 mm bore provides 982 N. Because this 190 mm stroke is a non-standard length, expect a made-to-order lead time.
This cylinder uses a PT1/4 port and a 16 mm rod with an M12x1.25 thread. Since the stroke exceeds 150 mm, ensure the piston rod is adequately supported against bending by using an external guide rail to prevent excessive side loading. As a standard double-acting cylinder, it will drift if air pressure is lost; if your application requires strict position holding, consider the BSE rod-lock variant. Its standardized ISO 15552 mounting dimensions allow it to serve as a direct replacement for comparable profile cylinders.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
Yes, it is dimensionally interchangeable with other ISO 15552 profile cylinders and shares standard mounting accessories. However, this specific SKU does not include a built-in magnet (-S), so it cannot host CMSE reed or DMSE electronic sensors for position feedback.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.