
The AirTAC SE40 Standard Cylinder SE40X200S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 200mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X200S is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
Equipped with a built-in magnet (S option), this unit supports AirTAC CMSE reed and DMSE electronic position sensors along the three integrated sensor grooves. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration, softening hard impacts during high-speed cycling.
| Model | Airtac SE40 Standard Cylinder SE40X200S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a routing flap on a packaging conveyor, using the 628 N push force to redirect heavy cartons at 30-800 mm/s.
Drives a horizontal tool ejection mechanism, relying on the 200 mm stroke and DMSE electronic sensors to confirm tool release.
Deploys a physical stop pin on a roller conveyor to halt inbound pallets, utilizing the adjustable cushion to prevent bounce.
This 40 mm bore generates 628 N push at 0.5 MPa. If your payload is lighter, stepping down to the 32 mm bore yields 402 N push, while upgrading to the 63 mm bore provides 1559 N push for heavier loads. As a standard ISO 15552 profile cylinder, it serves as a direct replacement for any brand sharing the 40 mm bore, 200 mm stroke, PT1/4 port, and standard mounting interface. The included -S magnet enables precise end-position detection.
Because the 200 mm stroke creates an extended lever arm, verify that side loads do not exceed the 16 mm rod bearing capacity. For applications requiring the load to remain fixed when air pressure is lost or the valve is centered, note that this standard cylinder will drift; an external pilot-operated check valve or a BSE rod lock variant is required for true holding.
Quick checklist
The SE40X200S delivers 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. It features a PT1/4 port and a 16 mm hard-chrome rod.
No, a standard double-acting cylinder will drift if air pressure is lost or the valve is centered. The adjustable air cushion only decelerates the piston near stroke end; it does not lock the rod. For position holding, consider a BSE rod lock variant.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.