
The AirTAC SE40 Standard Cylinder SE40X210 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 210mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X210 is a double-acting, single-rod ISO 15552 profile cylinder with a 40 mm bore and a 210 mm stroke. Because 210 mm exceeds the standard 1200 mm maximum for this bore, it is supplied as a non-standard, made-to-order unit. It delivers a 628 N push force at 0.5 MPa and utilizes a PT1/4 port.
The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. Field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed cycling. Note that this specific SKU lacks a built-in magnet, so it cannot host CMSE or DMSE position sensors without modification.
| Model | Airtac SE40 Standard Cylinder SE40X210 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 210 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×210 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 628 N push force needed to slide heavy machine tool safety doors open and closed rapidly along the 210 mm travel path.
Drives mechanical arms to fold corrugated cardboard flaps on continuous packaging lines, utilizing the adjustable cushion to prevent jarring stops at high cycle rates.
Pivots a routing gate on a conveyor system to sort pallets, taking advantage of the tie-rod-free extruded profile for flush mounting in tight transfer zones.
When sizing this actuator, compare its 628 N push at 0.5 MPa against the smaller SE32 bore, which provides 402 N, or the larger SE50 bore, which yields 982 N if your payload demands more force. Remember that a plain SE cylinder cannot hold a load if air pressure drops or the valve centers; the piston will drift, so specify a BSE rod lock for fail-safe positioning.
For this 210 mm stroke, the 16 mm piston rod and M12x1.25 thread can handle moderate side loads, but any unsupported overhang risks bending the rod bearing. Always guide the load externally to prevent binding. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement sharing standard mounting hardware and footprint with other ISO 15552 profile cylinders.
Quick checklist
The SE40X210 delivers a push force of 628 N and a pull force of 528 N at 0.5 MPa. At 0.7 MPa, the push force increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 and serves as a direct replacement for other ISO 15552 profile cylinders using standard mounting accessories. However, this specific SKU does not include a built-in magnet (-S), meaning it cannot support CMSE or DMSE electronic position sensors out of the box.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.