
The AirTAC SE40 Standard Cylinder SE40X220S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 220mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X220S is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This clean profile simplifies fabrication while maintaining rigid structural integrity.
Equipped with a built-in magnet (S option), this unit supports AirTAC CMSE reed and DMSE electronic position sensors along the three integrated sensor grooves. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed 30-800 mm/s cycling.
| Model | Airtac SE40 Standard Cylinder SE40X220S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 220 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×220 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives folding mechanisms on packaging lines where 628 N of push force reliably tucks corrugated flaps before tape sealing at high cycling speeds.
Actuates routing gates on parcel conveyors, utilizing the 220 mm stroke to swing packages cleanly into secondary chutes without tie-rod interference.
Lowers electronic test probes onto circuit boards, relying on the built-in magnet and DMSE sensors to confirm precise 220 mm extension positioning.
Selecting the SE40X220S is ideal when your application requires 628 N of push force at 0.5 MPa. If your load demands less energy, you can step down to the 32 mm bore, which provides 402 N of push. Conversely, if you need greater thrust, stepping up to the 50 mm bore yields 982 N. Because this unit features a 220 mm stroke, the 16 mm rod and internal bearing face bending moments under heavy lateral loads; always support the tooling with an external guide to prevent premature seal wear.
As a standard ISO 15552 profile cylinder, it serves as a direct replacement for any dimensionally interchangeable ISO 15552 cylinder, sharing standard mounting accessories like FA front flanges or LB foot brackets. Remember that a standard double-acting cylinder drifts when air pressure is lost or the valve centers; if your process must hold a vertical load without live pressure, integrate an external pilot-operated check valve or explore the BSE rod-lock variant.
Quick checklist
At 0.5 MPa, the SE40X220S provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf at 1.0 MPa, and the operational speed ranges from 30-800 mm/s.
Yes. The SE40X220S features a standard ISO 15552 profile and mounting interface, making it dimensionally interchangeable with other ISO 15552 cylinders. It uses a PT1/4 port and standard mounting hardware for straightforward retrofits.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.