
The AirTAC SE40 Standard Cylinder SE40X225 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 225mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X225 is a double-acting single-rod ISO 15552 profile cylinder engineered for a 225 mm stroke. Operating at 0.5 MPa, it generates 628 N of push force and 528 N of pull force, making it well-suited for medium-duty automation tasks.
Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s. This specific SKU lacks a built-in magnet, meaning it is not equipped for CMSE or DMSE position sensing without modification.
| Model | Airtac SE40 Standard Cylinder SE40X225 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 225 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the suction-cup linkage on automated case erectors, utilizing the 628 N push force to fold and seal corrugated cardboard flaps at high cycling rates.
Actuates routing flaps on modular conveyor lines, relying on the 225 mm stroke to fully clear passing totes before retracting.
Positions sliding test-tube trays inside analytical instruments, where the smooth extruded profile barrel prevents external tie-rod snags in tight cabinet spaces.
When sizing this 40 mm bore actuator, consider stepping down to a 32 mm bore (providing 402 N push at 0.5 MPa) for lighter-duty clamping, or stepping up to a 50 mm bore (delivering 982 N push at 0.5 MPa) if your payload demands greater thrust. Because this is a 225 mm stroke, the 16 mm rod and M12x1.25 thread will experience increased bending moments under heavy lateral loads; utilizing an external guide rail is strongly recommended to prevent premature rod-bearing wear. As a true ISO 15552 profile cylinder, it offers a dimensionally interchangeable direct replacement for other ISO 15552 cylinders, sharing standard mounting hardware and a PT1/4 port. Note that the adjustable air cushion only decelerates the piston near stroke end and does not hold the load if air pressure is lost.
Quick checklist
The SE40X225 generates 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. It features a PT1/4 port and a 16 mm rod with an M12x1.25 thread.
Yes, the SE40X225 is dimensionally interchangeable per ISO 15552 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders, reusing existing mounting accessories like FA front flanges or LB foot brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.