
The AirTAC SE40 Standard Cylinder SE40X229S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 229mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X229S is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering 628 N of push force at 0.5 MPa. Its 229 mm stroke is a non-standard made-to-order length, providing exact travel for specialized machine movements without compromising the standardized mounting envelope.
The extruded aluminum barrel omits external tie rods, yielding a compact body that resists corrosion and mounts flush against frames. Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushion at both ends can be tuned to absorb kinetic energy smoothly at speeds up to 800 mm/s.
| Model | Airtac SE40 Standard Cylinder SE40X229S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 229 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×229 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding arm on a packaging line, utilizing the 229 mm stroke to clear varying box widths while applying 628 N of push to seal flaps securely.
Actuates a routing diverter on a conveyor system, where the compact tie-rod-free profile allows flush mounting inside tight transfer zones.
Opens and closes a CNC safety enclosure, relying on the built-in magnet and DMSE electronic sensors to confirm door closure before machining cycles begin.
When sizing this actuator, compare its 628 N push at 0.5 MPa against neighboring bores: stepping down to a 32 mm bore yields 402 N, while stepping up to a 50 mm bore provides 982 N. Because the 229 mm stroke is a non-standard length, expect a made-to-order lead time. For direct retrofits, verify the PT1/4 port, M12x1.25 rod thread, and required mounting accessories like FA or LB brackets. Since the stroke exceeds 300 mm, consider an external guide to prevent rod-bearing bending under heavy lateral loads.
This standard SE cylinder does not hold its position when air pressure is lost; the piston will drift if the valve is centered or exhausted. If your application requires static load holding without live pressure, integrate an external pilot-operated check valve or specify a BSE series rod-lock cylinder.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes. The SE40X229S is manufactured to the ISO 15552 / VDMA 24562 standard, making it dimensionally interchangeable with other ISO 15552 profile cylinders. You can reuse existing mounting hardware and sensor brackets, though you should confirm the PT1/4 port thread matches your existing fittings.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.