
The AirTAC SE40 Standard Cylinder SE40X254S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 254mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X254S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a push force of 628 N at 0.5 MPa. Its 254 mm stroke is a non-standard made-to-order length, tailored for specialized travel requirements beyond the standard 250 mm increment.
This unit features a square extruded aluminum barrel without external tie rods, allowing for flush mounting and high corrosion resistance. Equipped with a built-in magnet (-S), it supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends can be tuned to decelerate loads smoothly, while the M12x1.25 rod thread handles secure mechanical coupling.
| Model | Airtac SE40 Standard Cylinder SE40X254S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 254 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×254 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 254 mm stroke to push packaging pallets cleanly across transfer lines, relying on the 628 N push force to overcome sliding friction.
Deploys the 16 mm rod to fold corrugated cardboard flaps at high speed, tuning the adjustable end cushions to prevent crushing the box edges.
Feeds sheet metal into a press brake with repeatable accuracy, using the built-in magnet and DMSE electronic sensors to confirm material placement.
When sizing this 40 mm bore, you can step down to the 32 mm bore for a lighter 402 N push at 0.5 MPa, or step up to the 50 mm bore to gain 982 N of thrust. Because this is a 254 mm stroke, the unsupported piston rod is susceptible to bending under side loads; always use an external guide rail to prevent rod-bearing wear. As a true ISO 15552 profile cylinder, it serves as a direct replacement for any standard 40 mm bore with a PT1/4 port, matching standard mounting accessories like FA or LB brackets. Note that the adjustable air cushion only decelerates the piston near the end of travel—it does not hold the load if air pressure is lost. For position holding, explore a BSE rod lock variant.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE40X254S is dimensionally interchangeable per ISO 15552, meaning it shares the exact same mounting footprint, PT1/4 port size, and M12x1.25 rod thread as other standard 40 mm profile cylinders, allowing for seamless retrofits.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.