
The AirTAC SE40 Standard Cylinder SE40X25SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 25mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X25SN is a double-acting single-rod ISO 15552 profile cylinder engineered for compact actuation. It delivers 628 N of push force and 528 N of pull force at 0.5 MPa, utilizing a 16 mm rod and an M12x1.25 thread. The extruded aluminum barrel lacks external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machine frames while freeing up lateral space for adjacent tooling.
This specific configuration includes a built-in magnet for non-contact position sensing with CMSE reed or DMSE electronic switches, alongside an NBR seal for standard operating temperatures. The integrated air cushion at both ends is field-adjustable, allowing you to tune end-of-stroke deceleration via a set screw rather than relying on a fixed rubber bumper.
| Model | Airtac SE40 Standard Cylinder SE40X25SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 25 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Applies 628 N of clamping force at 0.5 MPa to secure aluminum workpieces in CNC milling fixtures, utilizing the 25 mm stroke for rapid actuation.
Drives folding mechanisms on continuous motion case sealers, where the compact 40 mm profile and adjustable cushion prevent harsh impact at the 25 mm stroke end.
Ejects small stamped metal parts from progressive dies, using the integrated magnet to trigger DMSE sensors for part-present verification.
With a 25 mm stroke, the SE40X25SN is tailored for very short, high-cycle clamping or ejection tasks. If your application requires less force, stepping down to the 32 mm bore yields 402 N of push at 0.5 MPa, whereas moving up to the 50 mm bore provides 982 N. Because this is a standard double-acting cylinder, it cannot hold a load unpowered—should you need mid-lock positioning or fail-safe holding during air loss, consider the BSE rod lock series. For ISO 15552 dimensional interchangeability, match the 40 mm bore, 25 mm stroke, PT1/4 port, and your required mounting accessory.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes. The SE40X25SN is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can drop it into existing mounts matching the 40 mm bore footprint, PT1/4 port, and 25 mm stroke, provided your setup accommodates the NBR seal and CMSE/DMSE sensor magnet.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.