
The AirTAC SE40 Standard Cylinder SE40X290S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 290mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X290S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a push force of 628 N at 0.5 MPa and a maximum push capacity of 128 kgf at 1.0 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact body that mounts flush and resists corrosion while integrating sensor grooves on three sides.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic position sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows you to tune deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s.
| Model | Airtac SE40 Standard Cylinder SE40X290S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 290 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×290 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 628 N push force and 290mm stroke to push cartons cleanly between parallel packaging belts operating at standard cycling speeds.
Leverages the -S magnet with DMSE electronic sensors to confirm full 290mm extension when ejecting processed test tubes from a centrifuge carousel.
Controls the sequential release of bare circuit boards into a pick-and-place machine, relying on the smooth adjustable cushion to prevent end-stop shock.
This 40mm bore generates 628 N of push at 0.5 MPa; if your application requires less force, the 32mm bore offers 402 N, while stepping up to the 50mm bore provides 982 N. Because the 290mm stroke is substantial for a 16mm rod, the unsupported piston is susceptible to side-load bending—pairing this cylinder with an external guide rail prevents rod-bearing wear. As a true ISO 15552 profile cylinder, it serves as a direct replacement for any standard 40mm bore, 290mm stroke unit with a PT1/4 port and basic mounting. Note that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load if air pressure drops, so a BSE rod lock is required for fail-safe holding.
Quick checklist
At 0.5 MPa, the push force is 628 N and the pull force is 528 N. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE40X290S is dimensionally interchangeable per ISO 15552, meaning it shares standard mounting dimensions, a PT1/4 port, and a 16mm rod thread. You can drop it into existing tooling designed for standard ISO 15552 profile cylinders.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.