
The AirTAC SE40 Standard Cylinder SE40X320S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 320mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X320S is a double-acting single-rod profile cylinder operating at 628 N push and 528 N pull at 0.5 MPa. Built to the ISO 15552 standard, its extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
This 40 mm bore unit includes a built-in magnet (-S) for direct compatibility with AirTAC CMSE reed and DMSE electronic sensors. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration, protecting the 320 mm travel path from harsh mechanical impacts.
| Model | Airtac SE40 Standard Cylinder SE40X320S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 320 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×320 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 320 mm stroke and 628 N push to extend and redirect cartons between parallel packaging conveyors without stalling the main line throughput.
Leverages the flush-mount profile and CMSE/DMSE magnet sensing to sequence the safe opening and closing of a 320 mm travel machine safety enclosure.
Deploys the 528 N retract force to firmly catch and halt incoming pallets at a robotic pick station, absorbing kinetic energy via the adjustable cushions.
If 628 N of push is insufficient, stepping up to the 50 mm bore yields 982 N at 0.5 MPa; conversely, dropping to the 32 mm bore reduces output to 402 N for lighter loads. As a true ISO 15552 cylinder, this model is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing direct retrofits using existing mounting hardware.
Because the 320 mm stroke creates a long unsupported rod extension, side loads can induce bending moments on the rod bearing. An external guide mechanism is recommended to prevent premature seal wear. Note that the adjustable cushion only decelerates the piston near stroke end; it does not hold the load if air pressure is lost.
Quick checklist
At 0.5 MPa, the SE40X320S provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating speed ranges from 30-800 mm/s.
Yes, the SE40X320S is dimensionally interchangeable per ISO 15552 standards. You can direct replace other ISO 15552 profile cylinders using the same mounting accessories, port size (PT1/4), and rod thread (M12x1.25) without machining new brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.